CPLD (or FPGA) implementation of LCD bus converter

$250-750 USD

Færdiggjort

Slået op

over 5 år siden

$250-750 USD

Betales ved levering

The goal of the project is to translate an LCD bus with propriety signaling to drive a standard off the shelf LCD using RGB interface. In addition, the image will require interpolation while keeping the original aspect ratio. Source device will be provided + timing chart of source. Output LCD + LCD controller datasheet + init code will be provided. Development board will NOT be provided (you should have your own). VHDL is preferred but not obligatory, Verilog can also be used. Altera family devices should be used. Project should be oriented towards low power and low cost since day 1. Information about further requirements (some software features) will be provided later. Please read this before quoting. Please do not quote if you can not complete this project. Please make sure this is something you are able to complete within less than 30 days. The project is not very complicated and should be moderate difficulty for someone with FPGA development experience.

Electrical Engineering

Projekt-ID: 18641843

Om projektet

7 forslag

Projekt på afstand

Aktiv 5 år siden

Leder du efter muligheder for at tjene penge?

Emailadresse

Fordele ved budafgivning på Freelancer

Fastsæt dit budget og din tidsramme

Bliv betalt for dit arbejde

Oprids dit forslag

Det er gratis at skrive sig op og byde på jobs

Tildel til:

@petteriaimonen

I can deliver VHDL code for the converter in 14 days based on the timing and waveform information. If full information is not yet available, I can reverse engineer it with logic analyzer, but then there will be some delay due to shipping. I have a degree in digital systems and experience in working with Altera Cyclone and Lattice ICE devices. I will deliver: - standard vhdl 2008 source, synthesizable for most FPGAs - simulation testbench for the converter

$750 USD på 14 dage

5,0

(4 anmeldelser)

4,7

7 freelancere byder i gennemsnit $844 USD på dette job

@raulbehl

Hello! Please check my profile and reviews to know a bit about me and my work. It would be great if I could help you out.

$277 USD på 10 dage

4,9

(82 anmeldelser)

6,2

@prefectworld

Am a solid independent specialist, I am so eager to function as a consultant, I am a diligent employee, inspired by meeting set focuses inside due dates, as it gives me a feeling of achievement. I focus on points of interest and guarantee that my work will fulfil your desires. I likewise begin taking lessons to turned into an Experienced FPGA/Verilog/VHDL Engineer hand, to build up my aptitudes around there. I can state I am a genuine all-around collaborator with the capacity to deal with all parts of business while expanding general profitability with effective work.

$250 USD på 3 dage

4,8

(17 anmeldelser)

4,7

@NabilHunt

Hi, I am an Electronics and computer science engineer, I have experience working with various prototyping boards, Raspberry Pi, Arduino, mbed (ARM proto board)... as well as developing custom PCBs, you can find some of my projects on my portfolio. I pride myself on ensuring that the customer is satisfied with the quality of the work and strive to sustain good communication and complete the project (5-star reviews/ 100% completion rate) Looking forward to working with you. Regards, Nabil

$2.941 USD på 25 dage

5,0

(7 anmeldelser)

4,4

@hungfreelancer

I have 10 years of experiences in design and verifying using Verilog/SystemVerilog HDL. I am using Quartus II (Altera) and Vivado (Xilinx) EDA toos. I think this may be a easy project with me. Please contact me. Best regards.

$333 USD på 10 dage