Microchip i2c exampleJobs

Hi, header of project says all. i want you to write me code for getting 8x 1 wire temp sensor (DS18B20) addresses automaticially and getting the sensor temperature in arduino. after that write the temperature value to two connected i2c devices from HORTER and display value as 0,2V-10,0V DC for -30°C until 50°C temperature. Only Payment after full finish of project. Give real amount as offer. Dont want some calculations with later on topups. Timeline is short as possible. Best is one or two days. Good luck!

I have a design of a cup x 2, I need to be able to print this shape of the cup and make a cut-out of it. I just need the outline in detail designed please.

I need a logo designed for agriculture company

Hello, I need help with a timer project for Arduino. This project will incorporate the small 0.96” OLED displays that use the Adafruit library. See attached details... Arduino Uno 0.96 Inch OLED Module 12864 128x64 Yellow Blue SSD1306 Driver I2C Thank you, Steve

hi there, We would like install btcpay () on our store built on drupal 7. You must show me at least one example of store that you personally have installed it. Otherwise, please do not bid this project. We will need install this on a test site ours first and then install it on a live site. Need to get it done in 2 days.

...device wherever possible 4) Test the devices in multiple scenarios and fix the bugs 5) Give production-ready firmware Skills Required: • Min 3 years of experience in firmware development especially in C, C++, data structures, RTOS, Linux, etc.. • Must have worked with ESP, STM32, Microchip, ATMEL line of microcontrollers • Experience with working on Timers, RTC, GPIO, EEPROM, LCD, C/C++, Data structures, 16/32-bit microcontrollers (any of PIC, STM, ESP, AVR) • Experience with working on UART, I2C, SPI. RS-232/485, GSM/GPS, GPRS, TCP/IP, UDP, WIFI, Zigbee, any of the IoT communication protocols like LoRa • Must have worked with any of the firmware development tools like Keil, STM32 IDE, Arduino • Experience in development wi...

write a shopify's customer page stencil like example page in upload files.

I need help with i2c working with the gyroscope I'm using STM32

Create simple arduino library to use PCA9674PW I2C I/O expander * method Init(Wire &I2cBus, bool AddressSwitch1, bool AddressSwitch2, bool AddressSwitch3); we want to have I2C as reference. The i2c wire will be declared and initialised in main project and referenced only because we need to share I2C with another devices declared in main project. * Method SetOutputs(bool Out1, bool Out2, bool Out3, bool Out4); * Method void ReadIO(); Where the bits 0-3 Inputs and bits 4-7 are Outputs And then lets have public union struct in library (byte Value and bools for Input 1-4 and ouptuts 1-4 (check fiel example) Targets: * Provide library with mentioned methods * Library should include Arduino example code Hints: You can simplify your work and y...

Create simple arduino library to use Display DEM 256128A FG...ST7565 (datasheet included) * method Init(Wire &I2cBus, bool S1, bool S2); we want to have I2C as reference. The wire will be declared and initialised in main project and referenced only. S1 = LCD pin D6 S2 = LCD pin D7 * Method WriteText(uint_8t Line, uint_8t Column, uint_8t Size, string Text); We need up to 5 sizes, but we can reduce it if neccesary. * Method DrawRectangle(uint_8t x, uint_8t y, uint_8t width, uint_8t height, bool fill); * Method DrawCircle(uint_8t x, uint_8t y, uint_8t diameter, bool fill); * Method DrawLine(uint_8t x, uint_8t y, uint_8t x2, uint_8t y2); * Method DrawPoint(uint_8t x, uint_8t y); Target: * Provide library with mentioned methods * Provide Arduino example code us...

Create simple arduino library t...AddressSwitch1, AddressSwitch2); we want to have I2C as reference. The i2c wire will be declared and initialised in main project and referenced only because we need to share I2C with another devices declared in main project. S1 = LCD pin D6 S2 = LCD pin D7 * Method WriteText(uint_8t Line, uint_8t Column, uint_8t Size, string Text); We need up to 5 sizes, but we can reduce it if neccesary. * Method DrawRectangle(uint_8t x, uint_8t y, uint_8t width, uint_8t height, bool fill); * Method DrawCircle(uint_8t x, uint_8t y, uint_8t diameter, bool fill); * Method DrawLine(uint_8t x, uint_8t y, uint_8t x2, uint_8t y2); * Method DrawPoint(uint_8t x, uint_8t y); Targets: * Provide library with mentioned methods * Library should incl...

Looking for someone with experience on the Microchip SAMR34 Lora Chipset and MiWi Protocol to make a P2P communication code based on existing and working demo code base from Microchip. The task is to send any data using the UART interface from one node to the other. In order to achieve a bio-directional UART pipe between two modules for data transfer. Development should be done using Atmel Studio

We are looking to control an ST NFC chip (ST25R3916) from a Silicon Labs EFR32 (BGM210P) bluetooth module over an I2C connection. We would like the NFC chip to emulate a card and broadcast a NFC-A NDEF payload, as well as read other NFC-A NDEF payloads from tags placed onto the NFC coil. It would involve porting existing ST NFC libraries over to the silicon labs EFR32 platform and setting up communication with the NFC chip over I2C from the controlling EFR32 chip. You will be working with our in-house firmware engineer to achieve the required goals. We can ship hardware to you if needed, although mocking up the hardware implementation via development kits or working with our in-house engineer to test firmware on the actual hardware would be ideal. EFR32 firmware develope...

We have a IAR project build that generate some binaries. I need a script that flashes these binaries onto the device side(here the device we are using is the Microchip ATSAME54). The options that we have to flash the binaries using the flash programmer like Open OCD, CMSIS-DAP or ATMEL.

Based on a example remake a flyer, already have the logo and pictures Need to add text effect Give back fonts , psd and pdf read to print Give back size to print A5 – and A3 Can use the old psd file flyer to reuse food picutures

I am looking to make a website with custom products for people to design. My supplier has an excellent 'form' to upload your own images while also showing previews. I was wondering if it was possible to use my suppliers form or recreate it on our own.

Python coding for UAV onboard computer, (Odroid, Ubuntu). Get data from sensors (I2C, UART, etc.) and send information parameters changes to or from Flight Controller vie Mavlink communication. The code should be written with remarks and should be very easy to change by a user. Thank you Rotem

Hi, We would like to have the same header menu + sub menu style as on our website

We are looking for someone with working knowledge of the Microchip ATSAMR35J17 wireless LoRa device, to write the operating firmware to drive a new wireless sensor under development. The code should be simple, taking a reading from a sensor every 5 minutes, storing locally, then sending a min/max/average message every 1 hour unless a threshold has been breached. The device needs to be able to be configured with operational settings including RF settings. The PCB is designed, laid out and manufactured with components populated ready for firmware.

Recreate this logo making it a bit more updated, keeping colors similar and making it still fun. Correct abbreviation for Wisconsin from "Wisc"To "WI" Also, please alter the current .jpg to a transparent png.

I would like to create a working OmniPay example () to take SagePay payments () I would like a simple form to enter billing address, delivery address and card details, to process a SagePay card transaction using OmniPay. This will be integrated into a basic system allowing us to request payments from customers. I am looking for a developer with attention to detail, and who writes clean, dry and well-commented code. If you are this kind of developer, please be sure to TELL ME in the bid. I do not respond to copy and paste bids.

I'm looking for someone who can write example briefing notes. The notes are on topical issues relevant in Canada (you can suggest a topic or write on one of mine). The audience is executives in Canadian government. The briefing notes are for examples in a writing workbook, not for actual use with the target audience. However, I want them to be as authentic as possible. I might introduce errors so that workshop participants have to rewrite them.

We need people WITH EXPERIENCE in PHPoC , please dont offer if you never use this boards . What we need is to make a webserver that shows status of DI , AI and I2C sensors and send alerts based on client setup, so a page for admin, and a page for monitoring. Firmware must provide services HTTP SMTP and SNMP .-

I need someone with good i2c protocol knowledge. I am building device which act as a master and slave at the same time and use i2c one on the SDA SCL as a Master and act as a slave on second i2c on the SDA1 and SCL1. Device receiving information as a slave device from Master then uses some collected data and then pass it via second i2c line to another slave device. Slave devise send back another data and this data will be sent back to master device. Please bid only if you familiar with stm32 controller and able to provide clean professional C code to able to compile via Arduino IDE. Using Logic Analyses essential. For testing purpose possible to use Arduino Due

Using dspic33ep32mc202 and family reference manual available from microchip configure ADC to 1. 4 channel sampling 2. Simultaneous sampling 3. Auto sampling 4. Timer 3 triggers ADC 5. Enable ADC interrupt 6. Turn on ADC 7. Handle interrupt 8. AN0,1,2 and AN5 should be sampled

(I am using PIC Microcontroller (microchip) only, thus do NOT offer me code in ATmega, PLC, Arduino, Raspberry Pi, etc. and do NOT bid for the project if you are not able to send sample code) I need a working code to be written into PIC Microcontroller family where a crystal of 12MHz is being used. It is a device that will detect object (Object Detection) using IR sensor (RX and TX). Learning from past experience, I decided to make a sample/skill test to check you capability of PIC programming prior in awarding this project. Real project will be almost the same. Please see attached file (sample/skill test project) for further description. Basically it is a simple code (involving LEDs lighting sequence, sending/receiving USB data, receiving input from IR(Rx)) if you know what you...

I am building a fiber blower of sorts. I want to utilize a nema 23 with TB6600 driver and Arduino Nano with a I2C 16x2 display. Should have 4 buttons with + , - , START ,STOP functions. The device will work as follow. Nema connected to a wheel and another free spinning wheel on opposite side ,fiber cable will be inserted between them. On the LCD i would like to say 2000m length and hit start ,the motor should rotate feeding the cable through wheels for 2000m. However if i do not want to use a preselected length i can just hit start and it will feed until i select stop in this case it should still be measuring so once i hit stop it should be able to tell me how many meters has been pushed. Obviously i will need to calibrate this per cable thickness etc which is fine. I thought of usi...

I need a new website. I need you to design and build it.

C Code for Microchip dsPIC33CK256MP508 to configure and read accelerometer and gyroscope data from IMU ST ISM330DLC using SPI.

I am looking for a running simple C#-WPF-MVVM program example for a complex Datagrid type using Mahapps: Language: - Must be C#-WPF-MVVM - Must use Mahapps Features: - Datagrid where every cell is an independent UserControl compound of a Label, a TextBox, a ComboBox and a CheckBox: depending on a variable, we will enable one of them (only one of this behaviours is active at each time) - Headers must allow ordering rows by clicking (typical datagrid behaviour) - Columns must adjust automatically on content length (desired best solution) or their width can be modified with mouse (acceptable, typical datagrid behaviour) - XAML must not use triggers or styles MVVM model is to be used. - You will have to bind the Datagrid to my model objects, please see the attached screenshot and/or...

...using a Raspberry Pi 3. Given his age and interests, all I would like is a Python 3 script that will light up a SparkFun Qwiic Button () connected to the Pi via a SparkFun Qwiic Shim () and play an MP3 or WAV file of my choice via either the 3.5mm audio port or bluetooth when the button is pressed. These Qwiics use the I2C bus. An extension of this project would be to use the Pibrella board/hat () mounted on top of the shim to control the operation of the sound playback. There are red, yellow and green LEDs on this board and a large red button. I'd like the button to cause the LEDs to cycle (green -> yellow -> red) and be able to have different (or no) audio files play when the Qwicc button is

We would like to have code for MSP430-4133 MCU which would read data over I2c/SPI and send that data over serial every 20 seconds. This device must run for 1 years on 1000mAh battery.

...using a Raspberry Pi 3. Given his age and interests, all I would like is a Python 3 script that will light up a SparkFun Qwiic Button () connected to the Pi via a SparkFun Qwiic Shim () and play an MP3 or WAV file of my choice via either the 3.5mm audio port or bluetooth when the button is pressed. These Qwiics use the I2C bus. An extension of this project would be to use the Pibrella board/hat () mounted on top of the shim to control the operation of the sound playback. There are red, yellow and green LEDs on this board and a large red button. I'd like the button to cause the LEDs to cycle (green -> yellow -> red) and be able to have different (or no) audio files play when the Qwicc button is

The goal of this project is to where possible use small packets for shooting depending on the user need. Some customer systems require more data to be sent by the shot packet that others, this is largely determined by the theme. The system is written in Microchip C and uses MPAB IDE. The smaller the infrared packet, the more reliable the message is in a noisy outdoor environment. The type of packet used is set on the shooters gun. The target gun (or device) has to determine what packet structure is being received and process the packet accordingly. As well as 3 shot packets there is also general IR_SHORT and IR_LONG packets. In the current SATR 3 system all shot packets are the same length with 50 data bits plus CRC32 error checking plus STX, DLE, and ETX, Full current d...

I have an example of the page I'm looking to have designed, will be a single page deisgn in html, and some js and functions/links.

I'm learning how to code in react native and I'm trying to develop an APP on my own (Android). Tho I can't easily understand a few concepts about navigation between pages. I would need someone to write for me a very simple example (made by 2 or 3 ), where it is possible to navigate between different screens. I already created the screens themselves , I would just need the connection between them. A skilled programmer in react native can solve my request in a matter of few minutes, maybe a half a hour. For this reason also the budget has been fixed fairly low.

I need you to design and build it. Please build a template for putting passage and allows user to highlight it, like I will put it on a website and please add functionalities to send data (number of correct answer) to MySQL database

...with proven Sourcode for ESP32 and the corespondening PWA-BLE Application. We just want have everything integratet on a small PCB (without Pinheader from Prototyping Boards): 1 x Micro USB-B Socket for Powering and Programming (wich should overlap the PCB to integrate into housing) 2 x LED-Outs (accessible via GPIO) 2 x Screw-Terminals (for each HX711, with E+, E-, A+ A- ) 4 x Mounting holes 1x I2C Pinout 1x 3.3V / GND Pinout Optional - Connector for LiPo (charging trough Micro USB-B Socket) - Microswitch for Programming (beside the USB-B Socket, accesibel trough pin-hole) The PCB should not exted the dimesion 5x14cm. I need complete files for PCB etching and assembly (BOM, Gerber, Schematics) EasyEDA ist not a must, could be in Eagle or any other Software. Thank you for y...

PHP basic and advanced tutorial description and example with the code in google docs.

Looking to create an email signature exactly like the example shown in the MS word file. User detail need to be editable. End Product has to be compatable with iOS and Outlook for Mac, PC etc For reference: Image file is hosted here (please do not rehost elsewhere)

Good day We have a example design for our webshop in Odoo and need freelancer to make this design in a module << ITS ONLY CATEGORY VIEW, NOT COMPLETE WEBSITE!>> DM for more info

I need someone with experience in Embedded Firmware Development. I want someone to teach me all these technologies. You should have experience with developing embedded C/C++ applications for embedded operating systems such as Linux, QNX Neutrino, Micrium μC/OS, etc. on ARM targets. Experience with protocols like RS232, RS485, Modbus, SPI, I2C is desirable. Experience in Coding C/C++ is required. RTOS knowledge is desirable.

as the example and source code below i need the same as :- here the source code to add it to my website ,

This project requires you to start with my example project created using MPLAB X IDE and MCC code configurator. This has some pin definitions and uses timers, uarts, RTCC and defines the USB host. The MLA Microchip Library provides examples writing a file to a USB Thumb drive. See mlav2018_11_26appsusbhostmsd_simple_demo (for example) The task is to use the MLA example or similar to add a simple demo of writing a text file to a USB Thumb drive into the provided project (USB_Thumb.X). Successful project completion will be confirmed by the USB_Thumb project being compiled by me, programmed into the evaluation board, connecting a Thumb drive, Removing the drive and confirming the file exists using a laptop or PC. Expectation of cost is between £50 a...

STM32F103 i2c for LTC2497 (ADC-IC) code required, ?I just need to read the 16-bits value and switch channels. To know that its not a robot please put (LTC2497) in your reply. Code in C.

Induction Motor Control Automation - there are two microcontrollers: One microcontroller is playing a role of Zero cross detector in the circuit, and Other microcontroller is for the current sensor. Using a MICROCHIP Curiosity HPC and a PIC18F45K22

I want a C# based sample source code to control my Skype program (ver 8.*). The latest version of the Skype (Desktop) program does not support Skype4com.dll. I want a simple WinForm UI source code that provides: 1. View the Contact List (Friends) 1. Answer to chat request.(Open Chat) 2. Send a text message 3. Receive text messages 4. Close chat and 5. You should be able to compile it into an .exe file. 6. The .exe can be executed on Windows10. P.S: Many people seem to think that it is easy to develop for only a simple ui. Please tell me how can u process skype functions WITHOUT Skype4Com DLL. i WANT receive chat request on the win form.

it is a board with stm32F051 micro with a rtc, eeprom and some other simple peripherals. The requirement states to validate that the board has good soldered connection. There is a simple led that will indicate 4 states: "testing", "press button", "Good", "Fail". There will be a document that has details about connections and specifics of the software required. IDE used will be STCube...some other simple peripherals. The requirement states to validate that the board has good soldered connection. There is a simple led that will indicate 4 states: "testing", "press button", "Good", "Fail". There will be a document that has details about connections and specifics of the software required. IDE used will be STCube f...

Hello i have an example for a site i want my sitle like him exatly open cart or anything i want it like him for sure

I am looking for a programmer to create a LCD User menu that will have various functions. The menu will be controlled by Four buttons. (UP, DOWN, ENTER, ESC) and the LCD screen is a I2C 20X4. ------ Menu Layout ----- Home (to be shown on Arduino start-up and if no buttons have been pressed for 60 seconds) Mode (Set a variable depending on the users selection) - Automatic - DMX DMX Address - 1- 254 (User can use the up and down buttons to scroll through numbers 0 to 254. When the user pressed the enter button it will save the number as a variable to the Arduino memory. If the user holds down the up or down button the numbers should scroll through quicker) Test (Set a variable depending on the users selection) - Yes - No Exit (Return to Home) I will sha...