PCB stands for Printed Circuit Board and is closely associated with Electronics. The layout of PCBs can be designed using PCB Layout software. If your electronics-related business needs help with PCB layout and designing, your best bet is to turn to expert freelancersâEUR(TM) help who can deal with such technical knowledge. You can post your PCB layout job and start obtaining bids from freelancer PCB layout experts. Start by posting a job today!

Ansæt PCB Layout Designers

Filtrér

Mine seneste søgninger
Filtrer ved:
Budget
til
til
til
Slags
Evner
Sprog
    Job-status
    25 jobs fundet, i prisklassen EUR

    I am looking for a hardware engineer who can design a Microcontroller based board with fire alarm sensor bus part of a Fire alarm panel. I am looking for both addressable and non-addressable. If you are familiar with the isolation of sensors in the bus that will be a plus.

    €300 (Avg Bid)
    €300 Gns Bud
    8 bud

    To use a processor of STM32F030C6T6 or equivalent which is available for ready stock and design a circuit to sense the battery voltage, PV voltage, load voltage, charging current, discharging current, battery temperature, load trip, load ON/OFF, etc. To ensure the battery charging from 22V considering the battery floating voltages. All charging programs are to be taken care of by the microprocessor, to calculate the battery SOC & battery cycle. To provide options to change the parameters & battery cut-off points

    €704 (Avg Bid)
    NDA
    €704 Gns Bud
    4 bud
    Designing a circuit 6 dage left
    VERIFICERET

    I have made a project which is basically creating electricity now I want to store that into a battery and then further convert that into ac so for that purpose I need someone who can help me out. Preferably U should be from Hyderabad so that I can show you the project and accordingly you can work on the circuit.

    €80 (Avg Bid)
    €80 Gns Bud
    6 bud
    Aileron TTW 6 dage left

    I have a tilting tricycle that performs as a virtual bicycle at speeds above 5mph. Below that it convert to a low tilt vehicle that can dynamic level as it crabs around at this speed compensating for rolling tilting surfaces like driveways and pot holes. I have developed a lock or and drive actuator. I can manually controller. I am using an analog electrolytic tilt sensor used in farm equipment and motor homes to level them. I want to switch to Arduino for better control of functions and debugging.

    €1110 (Avg Bid)
    €1110 Gns Bud
    15 bud
    design a HDMI PCIE card 6 dage left
    VERIFICERET

    Card specification The card should be PCIEx16 compatible. The card will use onboard power (could use SATA but preferably not). Have an onboard HDMI splitter (PI3HDX414) Have an onboard HDMI-CAT6 converter. The card should have two HDMI outputs. One of the outputs will have a female HDMI port connected to it. The second port will be concerted to an onboard HDMI splitter through the PCB the outputs of the splitter should be as follows one Female HDMI and the other three outputs connected to HDMI-CAT6 converters. The output of each of the HDMI-CAT6 converters will be connected to a FEMALE CAT6 Jack (RJ45) you will need to design the Schematics and PCB for this project.

    €118 (Avg Bid)
    €118 Gns Bud
    6 bud
    Remote Monitoring Stations 5 dage left
    VERIFICERET

    The project is to design and develop an embedded system for a remote monitoring solution that can read from 4 different analog inputs (between +5 V to -5 V), convert them to a digital equivalent using 12-bit ADC, and send it to the control station using LoRaWAN radio

    €908 (Avg Bid)
    €908 Gns Bud
    2 bud

    Smort is a newly established Smart Home manufacturer based in Australia. We are begining small but have some very ambitious plans for our future. Our products are target toward a gap we have identified in the Smart Home market and we are working with industry here in Australia to incoroprate our products into theirs. In developing our first product we have noted a requirement for one or two engineers/software developers who are profficient in, or can show evidence of previously delivered projects with; Micro-controllers, industrial design, z-wave standard (IoT devices), and/or platform integration. We welcome discussions and proposals on how you may be able to assist us in delivering the best possible product to market. Further discussions will provide greater details on the exact requ...

    €1135 (Avg Bid)
    €1135 Gns Bud
    22 bud

    I want a PCB designer who design a pcb . i want a pcb and circuit designer for a big project if anyone wnt to collaborate with me please message me. Thank You.

    €30 / hr (Avg Bid)
    €30 / hr Gns Bud
    36 bud
    Build a Smart Home App 5 dage left
    VERIFICERET

    Zero crossing detector Ac220V 50/60Hz Circuit Diagram + PCB + Gerber + .ino + ESP + Java Apps Nowadays home automation is a very popular device. Home automation is the automatic control of electronic devices in your home. These devices are connected to Bluetooth, which allows them to be controlled remotely. If you want to do business with home automation then you can buy our full package. What can you do with it? 1. With this project you can control the electric device in the room through your smartphone. 2. ioT and Bluetooth technology have been used in this project. 3. You will be able to control a total of 6 different electronic devices in your home. 4. You can control the speed of the fan in your room. ( Zero Crossing Detector ) 5. And this project will autom...

    €751 (Avg Bid)
    Lokal NDA
    €751 Gns Bud
    9 bud
    arduino ethernet shield 4 dage left
    VERIFICERET

    i want someone who has already worked on arduino ethernet shield with mega board. I want it to operate from desktop application through ethernet connectivity

    €21 (Avg Bid)
    €21 Gns Bud
    8 bud
    I need an electrical engineer 4 dage left
    VERIFICERET

    Problem with Tesla's Battery. Tesla's electric cars only go 250 miles before it needs to be recharged, Our product will double that or 500 miles before recharging. This device can be used in Spaceships, drones, Iphones, The applications are endless. We want to find an electrical engineer that will sign a non-compete clause and verify our findings. We are located in Maui.

    €48 / hr (Avg Bid)
    Lokal NDA
    €48 / hr Gns Bud
    2 bud

    Logro leer el directorio principal pero no logro vizualisar las sub carpetas y archivos dentro de ellas , ni recuperar el directorio principal al salir Reducir un poco el codigo para que pueda entrar imagenes ya que si las agrego , el scketh no compila Uso stm32f103t8c8 en arduino

    €19 (Avg Bid)
    €19 Gns Bud
    2 bud

    Need a stand alone BMS program that monitors temperature and flow rate for a minimum of 3 liquid loops: ASIC coolant loop, Domestic Hot Water, & Industrial Hot Water. BMS needs to communicate with BRAIINS OS software to manage ASIC operation to prevent ASIC overheating. BMS needs to be able to be controlled and monitored remotely.

    €527 (Avg Bid)
    €527 Gns Bud
    5 bud

    Hardware specifications I need to develop a 4G CAT1 tracker with SIMCOM A7672SA(with gps). Electronic Schematic(Diagram), PCB, Firmware, functional prototype Let's use the microcontroller of the SIMCOM module itself 1- positive input(acc) 1- Negative Input 2 - negative output 1-RS232 acerometer Input power from 9 to 80v. Internal battery backup. With internal battery voltage reading and external power supply. Firmware according to the attached protocol.

    €3366 (Avg Bid)
    €3366 Gns Bud
    16 bud
    Design a PCB using KiCAD 4 dage left
    VERIFICERET

    Make a PCB using KiCAD with * ESP32-WROVER-E-N4R8 * SHT41 * TCS34103M * Power supply through micro USB - design a step-down converter yourself All parts used must be available from Digikey.

    €13 / hr (Avg Bid)
    €13 / hr Gns Bud
    54 bud

    I would like to speak to someone who has experience in product design, small communication device, all existing tech, just making it work. Needs to be in Perth, WA. Thank you.

    €3277 (Avg Bid)
    €3277 Gns Bud
    15 bud
    €2888 Gns Bud
    8 bud
    PCB Compliance Test 3 dage left
    VERIFICERET

    I require a PCB compliance test. test will determine if PCB is capable of passing EMC/EMI compliance tests and all relevant tests relating to CE mark and FCC standards. 1: 2 x PCBs need to be tested. 1 is extremely simple with just 6 switches on it. the other is more complex. 2: Timeframe would be as soon as possible. these boards are fairly simple so shouldn't be too difficult.

    €23 - €292
    Fremhævet Forseglet
    €23 - €292
    13 bud

    I have a simple circuit that is a battery operated rgb color switcher that runs on a PIC10F202; When the button is pressed, the single RGB LED changes to the next color in the sequence. When the battery is installed, the unit is on, and when the battery is removed the unit is off. What I need is to have the code modified so that the uController behaves in the following manner: 1 Unit is off with battery installed 2 Button is pressed once 3 Unit turns on with last selected color illuminated 4 Successive button presses will cycle to the next color in the sequence (R->G->B->Y-C->M for example) 5 Unit will stay illuminated in the current selected color until, 6 Long press (2 seconds) will shut the unit off and save the last selected color in memory 7 Operation repeats as above ...

    €169 (Avg Bid)
    €169 Gns Bud
    36 bud

    PCB design, manufacture and firmware programming for a heating controller. It will involve multiple inputs and outputs, both digital and analogue, NTC,0-10v, pulse, CT, on-off, power supply, separate high quality touch screen controller, 8 gig SD storage, Modbus master, Lora, Zigbee (connection to Sonoff sensors), Wi-Fi and LAN. It must connect to a website for analysis of data and the ability to upload data and download instructions and update the firmware through the internet. The project will also include the development of the firmware, website apps ect. I do have a precious version written in C as an example. A full description of the firmware will be supplied after a NDA is signed.

    €3198 (Avg Bid)
    €3198 Gns Bud
    45 bud

    I need a circuit diagram consisting all the necessary transistors and logic gates , to provide power to a gps, a bluetooth, a small speaker , all powered by a small rechargeable battery. I need this circuit to be less power consuming and provide more efficiency

    €13 (Avg Bid)
    €13 Gns Bud
    13 bud
    fire fighter telephone system 2 dage left
    VERIFICERET

    I need experts to have good experience in power line communication to build firefighter telephone system by using addressable node

    €531 (Avg Bid)
    €531 Gns Bud
    13 bud
    GNSS receiver with TCXO or OCXO 1 dag left
    VERIFICERET

    This is the glymse of the project: This project uses multi-frequency and multi-constellation Global Navigation Satellite System (GNSS) receivers to receive and converting from the received International Atomic Time (TAI) to Coordinated Universal Time (UTC). Once received it syncs the onboard Temperature Compensated Crystal Oscillator (TCXO) or Oven-Controlled Crystal Oscillator (OCXO). Design Schematics, PCB and Firmware Development. Details of the Project will be discussed after evaluvation

    €182 (Avg Bid)
    €182 Gns Bud
    11 bud
    Frequency meter 20 timer left
    VERIFICERET

    The project is to read frequency from a magnetic sensor and display the reading on a stepper motor and oled display and design the PCB board.

    €264 (Avg Bid)
    €264 Gns Bud
    38 bud

    Hi, We have designed a PCB around the STM32F401 + SIM868E. This PCB has been designed in Altium and has some connection issues which needs to be resolved. So in short the PCB design needs to be validated and potentially reworked. Please contact for more information.

    €463 (Avg Bid)
    €463 Gns Bud
    50 bud