Filtrér

Mine seneste søgninger
Filtrer ved:
Budget
til
til
til
Evner
Sprog
    Job-status
    15 battery switcher jobs fundet, i prisklassen EUR
    website build using divi theme 6 dage left
    VERIFICERET

    build a website for battery selling (industrial)

    €153 (Avg Bid)
    €153 Gns Bud
    69 bud

    Hello every one i am looki...have this type project then bid not make bid blindly 1 . need filters male /female 2 . country filter 3. gifts and meke redeem coins 4 . play in lower network 5 . battery sufficient [log ind for at se URL] [log ind for at se URL]

    €360 (Avg Bid)
    €360 Gns Bud
    3 bud
    PromaPackTrack 5 dage left

    ...packaging is done via SMS messages, so it will be necessary that each tracker has an SMS chip. It is necessary that the hardware has a relatively low acquisition cost and has a battery that lasts for at least 2 years. In this platform, it will be possible to visualize all the packages where they are and when clicking on a package, to see some registers like

    €4841 (Avg Bid)
    €4841 Gns Bud
    29 bud

    We need to develop a project that monitors DFRobot Oxygen Dissolved Sensor and temperature Sensor in an aquarium using ESP32 LoRa and Lipo or 9V battery.

    €303 (Avg Bid)
    €303 Gns Bud
    15 bud

    ...mount an xpt2046 driver to manage the screen and the sc card. WIth 1 button: On/Off and a switch : Flash. The ESP8266 has to be also in charge of measuring the remaining battery using the ADC. If you think you can do it, start the bidding proposal with "ESP8266TFT". If you need more info or pictures of the existing (but discontinued hardware), do

    €1055 (Avg Bid)
    €1055 Gns Bud
    33 bud
    Simple PCB Re-Design 2 dage left
    VERIFICERET

    ...a shunt coil of an MCCB. The DC Supply from an MCCB comes from a Battery source and the PCB uses an external Case mounted high wattage resistor to drop the voltage from up to 600vdc down to 120vdc. The Case mounted resistors can be changed depending on the coil impedance and battery voltage. They connect to the PCB via terminals. Skill Checklist (Do

    €149 (Avg Bid)
    €149 Gns Bud
    25 bud
    Trophy icon Create a Logo 2 dage left

    Logo for a new brand of Battery for Hobbies, how scale aviation, drones, rc cars. The Name of Brand is RcXpower.

    €26 (Avg Bid)
    €26 Gns Bud
    32 indlæg

    ...dpress/7935874 However, we do have a lot posts in defualt post type and we need to switch these posts to the customized post type in our theme. I tried to use post type switcher plugin, the post type changed, but all the comments in defualt post type doesn't display in the customized post type. I ask the author of the theme, it looks like it requires

    €148 (Avg Bid)
    €148 Gns Bud
    44 bud

    We are looking for someone to develop the HMI graphics for a system that detects faults in the national grid and injects power to the factory to prevent these faults from effecting the factory. there will be 3 pages only. 1, showing available power in the system, system status, and the voltage on 3 phases. 2, showing events, recording every time the system activated. time and date, and duration (i...

    €542 (Avg Bid)
    €542 Gns Bud
    8 bud

    My Problem Statement is as follows 1) The device must be controlled from the far end (say 3-5 km) without GS...from the far end (say 3-5 km) without GSM 2) Device working information must be sent back to the control station continuously 3) The device will operate on a battery and we need to get this battery charging status back to the control station.

    €460 (Avg Bid)
    €460 Gns Bud
    19 bud

    Induction motor needs to be driven using battery bank. Required voltage range is up to 500 V and frequency range is from 40 Hz to 400 Hz. You are free to choose battery technology, their combination or whatever. Let me know your relevant experience and final bid amount for the project. Write Inverter at the beginning of Bid, so I know you understand

    €24 (Avg Bid)
    €24 Gns Bud
    12 bud
    Device housing prototype design 2 dage left
    VERIFICERET

    I need a housing for a device intended for outdoor use. It must be waterproof and should fit the battery pack and electronics modules. I need a simple solution for the prototype, which can be manufactured cheaply even in a volume of 1..5 pc. I am looking for someone who, in addition to cad-design skills, has the knowledge of materials

    €15 / hr (Avg Bid)
    €15 / hr Gns Bud
    39 bud
    Firmware creation IoT Device 1 dag left
    VERIFICERET

    ...SAM D20 – Intended application • The sensor HUB, All three sensors interface with the SAMD20 Via independent I2C ports. • Power control • Buzzer control • Test LED control • Battery and charger ADC readings Bluetooth-BGM13P – Overview • The BGM13P is a BLE 5 compliant module with an Integrated 32-bit ARM Cortex-M4 core processor at 38.4MHz. Sin...

    €1279 - €2558
    Forseglet NDA
    €1279 - €2558
    8 bud

    I need a device to connect 6 Thermistors and measure temperature, Device to work on -30C degree to +70 so all Electrical component should be suitab...transmitted to the server shows in graph, every 10 to 15 min interval. Need a mechanism to monitor the temperature instantly if we need, to pull data. Device should work on Battery for at least 2 weeks.

    €706 (Avg Bid)
    €706 Gns Bud
    41 bud

    It is my task to design and simulate a Distributed Control System (DSC) for a microgrid (Hybrid), which is composed of PV, Wind, Battery, CHP and fuel cell. Someone else has helped me to complete the part of the design and simulation in MATLAB and I am having the proper results now. But, since he has left me, I need someone to go through the whole work

    €12 / hr (Avg Bid)
    €12 / hr Gns Bud
    15 bud