
Closed
Posted
Paid on delivery
Project: Finish and verify a 100 × 90 mm, 2-layer microcontroller-controlled 12 V lead-acid battery charger. It uses an LM338 regulator, an 18-0-18 V transformer, and an STM32F030C8T6 with a 16×2 LCD. What's already done: • A complete netlist, a BOM, a KiCad schematic and an empty PCB with net classes and design rules. • Firmware written in C with CMSIS (untested). It covers constant-current/constant-voltage charging, four current settings (3/5/7/9 Ah), an NTC temperature cutback, reverse-polarity protection, four status LEDs, a buzzer and the LCD. What I need from you: 1. Review the schematic and fix any errors, including pin numbers and footprints. 2. Place and route the 2-layer PCB. Use wide copper for the 1 A charge path and keep the analog traces clean. Run DRC and send Gerber and drill files. 3. Compile the firmware, fix any issues, and calibrate the voltage, current and temperature readings on the bench. 4. Test with a bench supply and a resistor load first, then a real 12 V battery. Check charging, full-charge detection, battery removal, reverse polarity and over-temperature. 5. Write a short test report and a build guide. Skills needed: KiCad, power electronics (LM338 and MOSFET circuits), STM32 (register-level C, ADC, PWM, SWD), and EMC-aware 2-layer layout. Deliverables: KiCad project, Gerbers, drill files, pick-and-place file, final BOM, tested firmware (source and .hex), and a test report. To apply: send 2 similar projects, fixed quote, and your estimated timeline.
Project ID: 40794616
30 proposals
Remote project
Active 2 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
30 freelancers are bidding on average ₹7,965 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹5,500 INR in 7 days
7.5
7.5

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!
₹7,700 INR in 7 days
6.0
6.0

Our STM32 firmware and custom IoT hardware experience directly matches this charger’s combination of power electronics, embedded control and PCB delivery. I work with STM32 systems, register-level C firmware, embedded development and PCB layout, giving me the right technical foundation to complete both the hardware and firmware sides of your 12 V charger. I can review the KiCad schematic, verify pin assignments and footprints, route the 2-layer board with appropriate high-current paths and clean analog layout, then produce the manufacturing files and updated BOM. My background in electrical engineering, electronics and microcontroller-based hardware also aligns with compiling, debugging and calibrating the STM32 ADC/PWM firmware, LCD, protection, temperature sensing and charging logic. I can additionally support the bench validation and documentation deliverables, including the test report and build guide. I would be glad to take ownership of this complete PCB, firmware and verification package and deliver a clean, production-ready project.
₹5,500 INR in 7 days
5.3
5.3

My PCB layout experience and embedded-systems skills align directly with completing your charger board in KiCad. I can work from the existing schematic, netlist, BOM and design rules to review the circuit, verify pin numbers and footprints, and produce a manufacturable 2-layer layout within the 100 × 90 mm outline. I can also support the power-electronics and firmware portions of this project, including the LM338 charging path, MOSFET-related circuitry, wide-current routing, clean analog layout, and STM32-controlled functions. My electronics and embedded-systems background is relevant to checking ADC, PWM, temperature sensing, protection features and the LCD/LED/buzzer connections. PCB Layout is one of my listed core skills, and I will provide the finalized KiCad project, Gerbers, drill files, pick-and-place data and BOM along with the firmware source and HEX where applicable. I am ready to complete the design verification, firmware compilation and charger validation professionally, including the requested test report and build guide. Choose me to take this charger from its current design files to a documented, production-ready result.
₹5,500 INR in 1 day
5.1
5.1

This is not an AI-generated bid like all the others I saw. As you can see in my portfolio on my profile, I have extensive experience designing PCBs and mass production equipment, just like you need. I can handle your project. I apologize for the simple proposal; I know you're probably tired of reading AI-generated proposals, and I'd rather not waste time on that. If you're interested in working with me, send me a message and we can work out the details! Best Regards!
₹15,000 INR in 15 days
4.8
4.8

I have experience in STM32-based electronics, battery charger circuits, power management, and PCB design. We also have a dedicated hardware testing lab for testing and debugging. I can also share examples of my previous projects to demonstrate my experience. A working netlist and untested firmware is a good head start, but the real risk here sits in two places: the 1 A charge path on a 2-layer board and the ADC calibration on the STM32F030's 12-bit converter. I've taken charger and power-path boards from schematic review through bench validation before, and the LM338 thermal budget is where most of these builds quietly fail. Here's what I bring to this: → I've shipped STM32 register-level firmware with ADC/PWM on custom power boards — including a solar RFID water vending controller on ESP32 that ran fully offline with valve metering and quota logic, tested in our lab before shipping to South Africa. → I've done EMC-aware 2-layer layouts with wide copper for current paths and separated analog domains, plus full DRC-to-Gerber handoff — my custom ESP32-C3 air quality monitor went from schematic to fabricated, tested units in 16–18 days. → Firmware, PCB design, 3D enclosure and prototype shipping all sit in-house, so nothing gets handed off between vendors. My approach: → Review the KiCad schematic against the LM338 and MOSFET datasheet pinouts, fix footprint mismatches, then place and route with the charge path widened and analog traces kept clear of the switching node.
₹6,000 INR in 3 days
3.5
3.5

Hi, I work in KiCad PCB design, power electronics, and STM32 CMSIS firmware — this project matches my stack directly. Two similar projects: STM32 power controller board — 2-layer KiCad layout for a regulated DC supply with LM317-family CC/CV output, ADC-based current and voltage sensing, SWD-flashed CMSIS firmware, and 16×2 LCD status display. Delivered Gerbers, BOM, and tested firmware. Embedded controller with NTC and protection circuits — STM32F0, CMSIS register-level C, NTC thermal cutback, multi-LED status, buzzer, reverse-polarity path. Full schematic review through DRC-clean Gerber output. What I’ll deliver: corrected schematic (footprints, pin numbers, LM338 circuit, reverse-polarity path), DRC-clean 2-layer layout with wide copper on the charge path and clean analog routing, compiled and bench-calibrated firmware (ADC: voltage, current, NTC), full fault-condition testing (resistive load, real battery, reverse polarity, over-temp, battery removal), plus Gerbers, drill, P&P, BOM, .hex + source, test report, and build guide. Fixed quote: ₹5,500 Timeline: 7 days from KiCad file handover XinTian
₹5,500 INR in 7 days
3.4
3.4

Our electronics engineering background combines PCB layout, embedded systems, microcontrollers, and complete hardware implementation—directly matching your STM32-controlled 12 V charger project. I can work from the existing KiCad schematic, netlist, BOM, and board rules to review pin assignments and footprints, complete the 2-layer layout, and prepare the required manufacturing files. My experience includes KiCad, Altium, Proteus, C/C++ embedded development, and practical electronic system integration. This supports the charger’s mixed requirements: careful high-current routing around the LM338 and MOSFET circuitry, clean analog measurement paths, STM32 peripheral firmware, and verification of the assembled system. I can also provide the finalized KiCad project, Gerbers, drill and pick-and-place files, BOM, firmware source and HEX, plus concise test and build documentation. I am ready to take responsibility for completing and validating this charger design and would welcome the opportunity to discuss the fixed quote and timeline with you.
₹5,000 INR in 7 days
3.6
3.6

Hello, I can help complete your STM32-based 12V lead-acid battery charger design in KiCad, starting with a technical review of the existing schematic and firmware. My proposed work includes: 1. Schematic verification: LM338 charging circuit, CC/CV regulation, STM32 connections, ADC interfaces, and component footprints. 2. Complete 2-layer PCB placement and routing, with attention to thermal management, power traces, and analog signal integrity. 3. ERC/DRC checks, Gerber and drill files, BOM, and manufacturing documentation. 4. Firmware compilation and review, subject to examining the existing code. 5. Assembly and verification guidelines. As an additional benefit, I will provide a professionally formatted LaTeX technical report FREE OF CHARGE, documenting the circuit architecture, engineering calculations, and PCB design decisions. I have experience with KiCad, embedded hardware, analog electronics, and power-management circuits. Could you share the existing KiCad project and firmware? Also, is an assembled prototype available for physical testing? My quote is ₹6,000 with a 10-day timeline for design review, PCB completion, and documentation. Physical testing and calibration would require separate arrangements. Best regards, Hamza
₹8,500 INR in 9 days
3.1
3.1

Your charger is 90% there — the schematic, netlist and firmware skeleton exist, and what's left is the part that decides whether it ships or smokes: pin-level review, a clean 2-layer layout with a fat 1 A charge path, and real bench calibration against a live battery. Here's what I bring to this: → I've built LM338-based CC/CV chargers with STM32F030 control, NTC cutback and reverse-polarity protection end to end → Register-level STM32 C with ADC/PWM/SWD — I calibrate against a bench supply and resistor load before a real battery goes near it → Full stack in-house: KiCad schematic and layout, firmware, 3D enclosure, and tested prototypes shipped → I keep a bench with bench supply, electronic load and scope ready, so calibration starts the day files land My approach: → Review your schematic against the STM32F030C8T6 pinout, fix footprint and pin errors, then lock net classes → Place and route the 2-layer board — wide copper on the 1 A path, analog ADC traces kept away from switching nodes, DRC clean, Gerbers plus drill and pick-and-place out → Compile and fix the firmware, calibrate voltage/current/temperature, run the full test matrix, and hand over the KiCad project, BOM, .hex, source and a short test report with build guide
₹5,000 INR in 2 days
3.3
3.3

Hi, there. I recently completed a 95 × 88 mm 2‑layer charger for a 12 V Ni‑MH pack using an LM337 regulator, an 18‑0‑18 V transformer, and an STM32F103C8T6 with a 16×2 LCD. I implemented constant‑current/voltage modes, multi‑Ah settings, NTC‑based temperature shutdown, reverse‑polarity protection, LED status, buzzer, and LCD display, resolving high‑frequency EMI by aggressive decoupling and careful trace spacing. I am planning to audit the schematic: verify pin‑compatibility, correct all footprint mismatches, and enforce 28 oz/ft² copper on the charge path. I will place and route the board, keeping the analog front‑end isolated, using a 0.25 mm clearance for the LM338 to 12 V rail, and adding a 10 µF bypass across the regulator. The DRC will be run with KiCad 7.0, and Gerbers, drill, and pick‑and‑place files will be delivered. For firmware, I will compile with GCC‑arm, debug via SWD, and calibrate ADC readings by injecting known currents through a shunt resistor. I’ll perform bench tests with a programmable supply, then verify full‑charge detection, pull‑out, reverse‑polarity, and over‑temperature shutdown on a 12 V lead‑acid battery. A concise test report and build guide will conclude the deliverables. If I use my previous experience, your project will likely be completed successfully. Hope to discuss this in detail. Through detailed discussion, I think I can find the better solution to finish your project successfully. Thank you
₹5,500 INR in 7 days
2.6
2.6

My embedded-systems and C programming background makes me well suited to review and complete the STM32 controlled charger firmware, including ADC-based voltage/current/temperature monitoring, charging control, protection logic, LCD, LEDs and buzzer behavior. I hold a Bachelor’s degree in Computer Science and a PhD in Artificial Intelligence, with nearly 20 years of professional experience in software engineering and technology leadership. My combination of register-level programming experience, embedded problem solving and broad technical leadership would give this charger a careful, verification-focused finish. Choose me to complete and validate the project professionally.
₹5,000 INR in 7 days
2.2
2.2

Hi, I can help complete and verify your existing 12V lead-acid battery charger project using the LM338 regulator, STM32F030C8T6, and 16×2 LCD. Proposed Approach Review the existing KiCad schematic, netlist, component pin numbers, and footprints. Correct schematic errors and verify component connections. Complete the 2-layer PCB placement and routing within the 100 × 90 mm board dimensions. Ensure suitable copper width for the 1A charging path and proper separation of analog and power signals. Run PCB design-rule checks and generate manufacturing files. Compile and review the existing STM32 CMSIS firmware. Verify ADC measurements, PWM control, LCD operation, and temperature monitoring. Test charging functions, including CC/CV operation, full-charge detection, battery removal, reverse polarity, and over-temperature protection. Prepare the final test report and build guide. Deliverables Updated KiCad schematic and PCB project files. Gerber and drill files. Pick & Place (CPL) file. Final component BOM. STM32 firmware source code and HEX file. PCB design-rule check report. Hardware testing report and build guide.
₹5,000 INR in 15 days
2.3
2.3

Hello, I can review your KiCad schematic, complete the 2-layer PCB layout with proper analog isolation and ground planes, and verify the STM32 CMSIS firmware logic. Scope of Work I will deliver: Schematic & Footprint Audit: Review LM338 regulator circuit, NTC divider, reverse polarity protection, and STM32 pinouts. EMC-Aware PCB Layout (100 × 90 mm): Route heavy traces for charging currents, keep ADC analog paths noise-free, implement solid ground planes, and pass full DRC. Manufacturing Files: Provide complete Gerber, drill, pick-and-place (CPL), and updated BOM files. Firmware Review & Build: Review and clean up the register-level C code, calibrate ADC calculation formulas, and provide verified compile source files and .hex. Testing Guide: Provide a step-by-step bench calibration and testing procedure for you to validate on your physical battery setup. Note: I will provide complete design, firmware, and validation documentation remotely within 5 days. Physical assembly and bench testing will be guided via the test procedure. I am ready to review your KiCad project files and start right away.
₹5,500 INR in 5 days
0.0
0.0

Hi, Greetings from OSTronik India! We are a technology-driven company specializing in Power Electronics and Embedded System Design integrated with Artificial Intelligence (AI) and Mobile Application Development, delivering reliable, industrial-grade electronic and software solutions—from concept to mass production, all under one roof. Our in-house capabilities include R&D, Firmware Development, Hardware Design, Mobile Application(Android & iOS), Prototyping, and Scalable Mass Production, with a strong focus on quality, performance, and cost efficiency. Core Expertise: • Microcontrollers: PIC, STM32, ESP Family, AVR. • Microprocessors: Raspberry Pi • Development Tools: MPLAB X IDE, STM32CubeIDE, Arduino IDE, Atmel Studio, VS Code • Hardware Design: Industrial-grade multilayer PCBs using Altium Designer with optimized power design, isolation handling, and EMI/EMC compliance • Communication Protocols: UART, SPI, I²C, CAN, Modbus, MQTT, LAN, S-Bus, RS-485 Mobile Application Capabilities: • Custom Android & iOS mobile applications for device control, monitoring, and data visualization • Real-time dashboards, cloud connectivity, and secure user authentication • Seamless integration between IoT platforms and mobile apps We have successfully transformed multiple concepts into market-ready electronic and mobile-enabled solutions. We would be glad to share a brief reference video. Let’s schedule a meeting to discuss your requirements in detail. Best Regards, Team OSTronik India
₹5,500 INR in 7 days
0.0
0.0

Hi, Your project is 80% done: schematic, BOM, rules and CMSIS firmware exist. What is left is the risky 20%, so I'd do it in this order: 1) Schematic review: STM32F030C8 pinout and footprints, LM338 adjust network, the current-sense path, the NTC divider range and the reverse-polarity MOSFET orientation. I'll send a marked-up list before I route anything. 2) KiCad 2-layer layout: wide pours on the 1 A charge path, the LM338 on its heatsink area, and a star ground that keeps the ADC and NTC traces away from the switching and transformer side. DRC clean, then Gerbers, drill and pick-and-place files. 3) Firmware: build with arm-none-eabi-gcc and fix the warnings and errors. I'll check the CC/CV state machine, full-charge detection (taper current) and the battery-removed case. I'll also add a calibration mode (offsets stored in flash) for the V, I and T readings. 4) Bench test plan: first a bench supply with a resistor load, then a real 12 V battery. That covers charge, full-charge, removal, reverse polarity and over-temperature. I'll write a short test report and a build guide. Price: INR 5,500 fixed, 6 days. Bench calibration can be done on my side, or with your technician over a screen session using my step-by-step guide. Your choice. Quick question: is the 16x2 LCD in 4-bit parallel mode or I2C (PCF8574)? Aria Tajeri
₹5,500 INR in 6 days
0.0
0.0

Hi, I’m Nur Rahman, an electronics engineer specializing in KiCad PCB design and STM32 CMSIS programming, and I can complete your 12V battery charger project for ₹6,000 within 6 days. Having built similar microcontroller-controlled chargers and power electronics boards, I will thoroughly review your schematic, handle the 2-layer power/analog layout, debug and calibrate the CMSIS firmware, and deliver full production files alongside a test report and build guide.
₹60,000 INR in 6 days
0.0
0.0

Hi, I am a power electronics and embedded engineer, I can implement your 12V lead acid charger project fully. However, I strongly suggest a design pivot: driving high currents (5-7A) through an LM338 linear regulator will create intense heat and necessitate huge heatsinking. I propose instead to implement a dedicated current controlled buck converter with phase control circuit. This drastically reduces thermal dissipation, for a high-efficiency, high-performance system that easily fits within your 100x90mm footprint constraint. I'll update your KiCad schematic to this topology and lay out a clean, EMC-aware 2-layer PCB, debug your STM32 CMSIS firmware and thoroughly bench-test the new high-efficiency charging profiles. Let’s build a better board! PCB must be completed at 3 days
₹5,250 INR in 3 days
0.0
0.0

Hello, I am interested in completing the KiCad PCB design and verification for your STM32-based 12V battery charger. I have 1+ year of hands-on experience in PCB design and layout, including schematic-to-PCB implementation, component placement, multilayer routing, footprint verification, BOM checking, DRC and DFM analysis. I can contribute to: - Reviewing the KiCad schematic, netlist and component footprints. - Completing the 2-layer PCB layout within the specified 100 × 90 mm dimensions. - Using suitable copper widths for the charging current path. - Keeping analog signals separated from noisy power sections. - Checking component placement, grounding and routing. - Running DRC and preparing Gerber, drill, BOM and pick-and-place files. - Providing editable KiCad project files and design documentation. I am also familiar with PCB design considerations for microcontroller-based circuits. I would like to review the existing schematic, PCB and firmware before confirming the firmware debugging, calibration and battery-testing scope. My proposed fixed quote is ₹5,500, with an estimated timeline of 7–10 days, subject to the existing design condition and testing requirements. Thank you for considering my proposal.
₹5,500 INR in 7 days
0.0
0.0

**Electronics Design & PCB Engineer | Power Electronics | Control Systems** Skilled Electronics Engineer specializing in electronic circuit design, PCB design and development, power electronics, and control systems. Experienced in designing, analyzing, simulating, testing, and troubleshooting analog and digital circuits, power supplies, DC-DC converters, inverters, motor control circuits, and electronic control systems. Proficient in schematic design, PCB layout and routing, component selection, circuit optimization, hardware prototyping, and electronic system development. Strong knowledge of semiconductor devices, MOSFETs, IGBTs, operational amplifiers, sensors, microcontrollers, and embedded systems. Experienced in power conversion, control circuit development, electrical system modeling, signal processing, and hardware testing. Capable of managing the complete electronic development process, from concept and simulation to PCB fabrication, assembly, debugging, and optimization. **Engineering Software & Tools:** Proteus, MATLAB, Simulink, Altium Designer, KiCad, LTspice, Multisim, and AutoCAD Electrical. Passionate about electronics innovation, hardware development, power conversion technologies, and intelligent control systems, with a focus on designing reliable, efficient, and practical engineering solutions.
₹5,500 INR in 4 days
0.0
0.0

Agra, India
Payment method verified
Member since Sep 10, 2026
₹1500-12500 INR
₹1500-12500 INR
₹1500-12500 INR
₹100-400 INR / hour
$30-250 CAD
$1500-3000 USD
$250-750 USD
£20-250 GBP
$10-50 USD
$10-20 SGD / hour
$750-1500 USD
€12-18 EUR / hour
₹12500-37500 INR
£150-350 GBP
₹100-400 INR / hour
$30-250 USD
₹1500-12500 INR
$30-250 USD
₹1500-12500 INR
₹1500-12500 INR
$250-750 AUD
₹1500-12500 INR