I gang

PCB Design

Design a Circuit and PCB using the Maxim 78M6610-LMU

I need a circuit designed for use with four Maxim 78M6610-LMU Energy Measurement Devices. I would prefer that this is designed in either Eagle (or Altium). Deliverables are the design files, as well as a PCB that can be sent for manufacture. If you want to bid on this project, make sure you tell me what PCB package you like to use.

The circuit will need to have the capability, depending on the loaded parts to use external Current Transformers (CT’s) or ACS710-30 hall effect sensors.

Voltage sensing shall be done between incoming Active and Earth. The incoming AC supply shall be connected to a string of five 250K 0805 resistors in series, with an additional 1K 0805 resistor between the end of the resistor string and Earth forming a resistor divider. The connection between the 250K resistors and the 1K resistors shall be connected to one of the Voltage inputs on the 78M6610-LMU as appropriate.

The device shall allow an external voltage input of up to 12V DC for powering the device. The design will need to convert this down to 5V 1A.

There need to be 18 sockets for various inputs. Every second current input should be connected together with a thick track.

I2C Parts

4 x 78M6610-LMU

1 x FM24C256

2 x 4k7 for Pull Up

RS485

1 x MAX1485

Current Sensing

4 x ACS710-30

CPU Module

24 Pin DIP – 0.6” with 0.1” clearance on sides and 0.2” on ends

Vin – Pin 1

Ground – Pin 2, 20

V3.3 Out – Pin 22, 24

Reset – Pin 23

Serial Tx – Pin 3

Serial Rx – Pin 4

SDA – Pin 13

SCL – Pin 14

RS485 Device Enable – Pin 19

External Connections

16 Positions – Current Sensors

3 Positions – Voltage Sensor

2 Positions – DC Input

3 Positions – RS485 (2 + GND)

Possibly Dinkle 2EHDRC series ([url removed, login to view])

Possible Suppliers for Cases and Connectors

Jaycar ([url removed, login to view])

Altronics ([url removed, login to view])

78M6610-LMU

20 MHz Crystal

External Reset from CPU

IFC 0/1 Pins: IFC0 = 0; IFC1=1 for I2C Mode

Addr 0/1: set for 0/0, 0/1, 1/0, 1/1 for device 0,1,2,3 respectively

Færdigheder: Elektronik, Ingeniørarbejde, PCB Layout, Produkt Design

Se mere: 78m6610 lmu, www vin com, www scl, www electronics engineering com, the design files, scl, jaycar electronics, jaycar, engineering positions, engineering au, design pcb need, dc design, ct-engineering, circuit design com, Transformers, sensing, sda, RX, pin down, pcb design altium, pcb circuit, PCB altium, manufacture design, I2C, Eagle PCB

Om arbejdsgiveren:
( 93 bedømmelser ) Ingleburn, Australia

Projekt-ID: #6022031

Tildelt til:

fogexpert

Hello! Nice to meet you! I am a master of circuit design and PCB Layout. In particular, I have a lot of practical experiments in appliance of Microcontroller and PLC. If you want high quality, lower rate and speed, Mere

$80 AUD in 10 dage
(0 bedømmelser)
0.0

4 freelancers are bidding on average $335 for this job

TaurTech

Dear client, My name is Stefan Andrei Chelariu and I am an Applied Electronics Engineer from Romania. I would like to submit my candidature to this job because i have experience in such systems and i can design yo Mere

$225 AUD in 7 dage
(1 bedømmelse)
2.8
mandeeshc

Sir, Greetings from India. Hope you are doing great. We are a Team of Embedded System Developers involved in Freelancing and developing Embedded Systems based Projects, Product Development and also providing Embe Mere

$1000 AUD in 30 dage
(1 bedømmelse)
2.8
luonghoantien

Dear, I'm an electronic Engineer. Although i'm a new freelancer but I have many experience in PCB design. I''ll design your project by Eagle and send you .brd file. I commit to finish your project in 7 days. I won't m Mere

$35 AUD in 7 dage
(0 bedømmelser)
0.0