
In Progress
Posted
Paid on delivery
Need a production-ready custom PCB design for an AI talking companion. The prototype already works on an Electrobot ESP32-S3 development board. We need the schematic, PCB layout, Gerber files, and a complete Bill of Materials (BOM) so we can send the package to manufacturers such as Lion Circuits, PCBWay, or JLCPCB for fabrication, assembly, and component sourcing. What to design - Use the ready ESP32-S3-WROOM-1-N8R8 module (8 MB flash + 8 MB PSRAM). Do not design the bare ESP32-S3 chip, crystal, or antenna. - USB-C for programming and charging, using the ESP32-S3 native USB. No CP2102 or CH340. - I2S MEMS microphone that JLCPCB or LCSC actually stocks (MSM261S4030H0 or TDK ICS-43434). The prototype used INMP441, which is discontinued. - MAX98357A I2S Class-D amplifier and pads for a 3 W, 4 ohm speaker. Power the amplifier from the battery. - 0.96 inch SSD1306 OLED, 128x64, I2C. - Two user buttons, plus one hidden Boot pad. - One rechargeable lithium cell, charger with battery protection, power switch, and a 3.3 V regulator rated for at least 500–600 mA. - 4-layer board. Leave the antenna end of the module clear: no copper, screws, battery, or speaker magnet under that end. - Copy the Espressif ESP32-S3-DevKitC-1 circuit for the module, USB-C CC resistors (5.1 k ohm), 3.3 V rail, EN reset, and GPIO0 boot strap. - On N8R8, GPIO35, GPIO36, and GPIO37 belong to PSRAM. Do not use them for the mic, display, or buttons. - Put the microphone and the amplifier on the two I2S ports so talk and listen can run together. Deliverables 1. Schematic (KiCad preferred) 2. 4-layer PCB layout for a small desk companion 3. Gerber files (RS-274X), drill file, pick-and-place, and assembly drawing 4. Full BOM with manufacturer part numbers, quantities, and LCSC or JLCPCB part numbers where possible 5. Pin map so the existing firmware can drop onto the new board 6. Short DFM notes for a first run of 5 assembled boards Out of scope: plastic enclosure, firmware, and India wireless approval. We will share the hardware spec and custom board plan after hire. First boards are for electrical testing only.
Project ID: 40783386
28 proposals
Remote project
Active 7 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs

Hi, I can design your AI talking companion PCB using the ESP32-S3-WROOM-1-N8R8, with a complete KiCad schematic, 4-layer PCB layout, USB-C programming and charging, I2S microphone and MAX98357A amplifier, OLED interface, buttons, battery protection, and 3.3 V power regulation. I’ll follow Espressif’s reference design, preserve the existing firmware pin mapping where possible, and ensure GPIO35, GPIO36, and GPIO37 remain reserved for PSRAM. I’ll also keep the antenna area clear and prepare the Gerbers, drill files, pick-and-place, assembly drawings, and a complete BOM with manufacturer and LCSC/JLCPCB part numbers where available. I’ll include DFM notes for your first batch of 5 assembled boards, with a focus on reliable fabrication, assembly, and electrical testing. I’m ready to review your hardware specifications and existing prototype pin mapping so we can get started. Add a clear project deliverables listClarify the final files and testing scope
₹11,000 INR in 7 days
1.7
1.7
28 freelancers are bidding on average ₹7,197 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹10,000 INR in 7 days
7.5
7.5

Hello, I can help you turn your working ESP32-S3 prototype into a production-ready 4-layer PCB. I’ll design the schematic and PCB in KiCad, including native USB-C, battery charging and protection, a 3.3V power supply, I2S microphone and MAX98357A amplifier, OLED, and user controls. I’ll verify component availability through LCSC/JLCPCB, avoid GPIO35–37 on the N8R8 module, and keep the antenna area clear. I’ll also prepare the complete BOM, pin map, Gerbers, drill files, pick-and-place, assembly drawing, and DFM notes for your first five boards. The design will be organized for straightforward fabrication and assembly, with particular attention to power integrity, audio signal routing, and component placement. I’m ready to review your hardware specification and existing firmware pin map to ensure compatibility with the current prototype.
₹1,050 INR in 7 days
5.6
5.6

Hi, I’ve carefully reviewed your requirements, and this is exactly the type of project I specialize in. I have strong experience in ESP32-based hardware and PCB design. I can design your compact 4-layer PCB, integrating the ESP32-S3, USB-C charging, battery management, I2S microphone and amplifier, and OLED while ensuring compatibility with your existing firmware. You can also check my portfolio for examples of my previous ESP32 and PCB projects. I’ll deliver the KiCad source files, Gerbers, BOM, pick-and-place files, assembly drawing, pin map, and DFM notes. Best regards, Ahmed
₹20,000 INR in 14 days
4.6
4.6

Hi, Greetings. I am interested to work on your project. Please discuss design details and technical parameters. Looking forward to hear from you. Thank you Shivkant
₹25,050 INR in 7 days
4.7
4.7

At HardFault, we are excited about your project for designing a production-ready ESP32-S3 AI companion PCB. Our recent work with ESP32-based embedded systems aligns perfectly with your needs, especially considering our experience in designing custom PCBs and interfacing with components like the MAX98357A I2S amplifier and I2C MEMS microphones. We excel in translating prototyped designs into production-ready schematics and layouts, backed by a strong track record in embedded hardware design and IoT connectivity solutions. With our team, you'll benefit from a collective expertise that ensures a rapid turnaround, robust design considerations, and redundancy in skills – all vital for critical hardware projects like yours. Our approach will begin by reviewing any existing schematics you might have to align our deliverables seamlessly with your current firmware. Could you share more about the desired form factor or dimensions for the PCB, given its usage as a desk companion?
₹9,810 INR in 15 days
3.4
3.4

I have experience in ESP32-based embedded systems and custom PCB design, including schematic development, component selection, PCB layout, and hardware integration. Our team focuses on reliable, production-ready hardware solutions with proper power management, signal routing, and manufacturing documentation. I can help you develop a production-ready ESP companion PCB tailored to your project requirements. Your spec is already tighter than most briefs I get — N8R8 with GPIO35/36/37 reserved for PSRAM, INMP441 swapped for a stocked part, amplifier off the battery rail. That's the level I work at. Here's what I bring to this: → 4-layer ESP32-S3 boards with module antenna keep-out, USB-C CC resistors and GPIO0 strap copied from the DevKitC-1 reference — I've shipped an ESP32-S3 curtain controller through a 25-unit run with RS485 and MQTT on one board → I2S mic + MAX9837/98357A amplifier on separate I2S ports for simultaneous talk and listen, plus SSD1306 on I2C kept clear of PSRAM pins → KiCad schematic, layout, RS-274X Gerbers, drill, pick-and-place, assembly drawing, full BOM with LCSC part numbers, and a pin map your firmware drops onto → 5-board first run with DFM notes written against Lion Circuits and JLCPCB capabilities, so no rejection surprises
₹800 INR in 3 days
3.5
3.5

Hi, Please check my portfolio as I have completed several ESP32 S3 and audio based KiCad PCB designs for JLCPCB production. I can design your four layer AI companion board integrating the N8R8 module native USB C charging I2S microphone OLED and amplifier. I will strictly follow your GPIO routing constraints keep the antenna zone perfectly clear and ensure separate I2S ports for simultaneous talk and listen. I will deliver the complete KiCad schematic board layout LCSC optimized bill of materials pin map and manufacturing notes. Best regards
₹1,000 INR in 5 days
2.5
2.5

Your ESP32-S3-WROOM-1-N8R8 spec is refreshingly clear — swapping the discontinued INMP441 for a stocked MSM261S4030H0, keeping the antenna end clear, and dodging the PSRAM pins (GPIO35/36/37) already tells me you've been burned before. Here's what I bring to this: → I designed a custom ESP32-C3 air quality board (PM2.5, OLED, USB-C) that went from brief to fabricated. → Done I2S mic + MAX98357A audio on an ESP32 Bible audio player — 365 verses from internal flash, shipped working → Full in-house: schematic, 4-layer layout, Gerbers, BOM with LCSC part numbers, plus firmware if you want it later.
₹600 INR in 2 days
3.0
3.0

Hi, I have hands-on experience with multiple ESP32 projects, STM32-based I2S audio streamer modules, and an ESP32 internet radio using dual MAX98357A amplifiers for stereo output. I have also designed 4-layer PCBs, including a TPA3250 amplifier board and audio interface boards. I can design a manufacturing-ready 4-layer PCB for your AI talking companion using the ESP32-S3-WROOM-1-N8R8 module. Deliverables: • KiCad schematic and PCB layout. • USB-C native USB programming interface. • I2S MEMS microphone and MAX98357A amplifier with separate I2S interfaces for simultaneous audio input/output. • SSD1306 OLED, buttons, Boot pad, and firmware-compatible GPIO mapping. • Li-ion charging/protection, power switch, and 3.3 V regulator. • Complete BOM with manufacturer part numbers and LCSC/JLCPCB sourcing references. • Gerber, drill, pick-and-place, assembly drawing, and DFM files. I will focus on audio noise reduction, grounding, power integrity, USB connectivity, PSRAM pin restrictions, antenna clearance, and manufacturability. I will review your prototype connections, firmware pin assignments, and mechanical requirements before finalizing the design. I look forward to discussing your specifications. Best regards, Noushar Najeeb
₹8,000 INR in 5 days
2.5
2.5

I’m Ashmit Dabi, a Hardware/PCB Design Engineer experienced in embedded hardware, PCB design, and electronics development. I can design the production-ready 4-layer KiCad PCB around the ESP32-S3-WROOM-1-N8R8 while keeping the existing prototype firmware pin mapping compatible. I’ll handle the complete schematic and PCB design, including native USB-C programming/charging, battery power and protection, 3.3 V regulation, EN/GPIO0 boot circuitry, I2S MEMS microphone, MAX98357A amplifier, SSD1306 OLED, buttons, and the required power switching. I’ll specifically account for the N8R8 PSRAM-reserved GPIO35/36/37 and assign the two I2S interfaces so microphone input and audio output can operate together. For the RF section, I’ll follow the ESP32-S3 antenna keep-out requirements and ensure there is no copper or mechanical interference beneath the antenna end. Components will be selected with JLCPCB/LCSC assembly and sourcing in mind, including an available replacement for the discontinued INMP441. I’ll provide the KiCad source files, 4-layer PCB, Gerbers, drill files, BOM with MPN/LCSC references where available, CPL/pick-and-place, assembly drawing, firmware-compatible pin map, and DFM notes for the initial 5-board build. I can start immediately and work from your existing prototype/hardware specification.
₹5,000 INR in 2 days
1.7
1.7

Your production-ready ESP32-S3 companion PCB requires careful electronics engineering across power, USB, audio, display, and manufacturing constraints. My skills in Electrical Engineering and Electronics align directly with this work, including translating an existing prototype into a manufacturable custom board rather than treating it as a simple development-board adaptation. I can support the schematic and 4-layer PCB design around the ESP32-S3-WROOM-1-N8R8, native USB-C, protected Li-ion charging, 3.3 V regulation, SSD1306 I2C display, I2S microphone, MAX98357A amplifier, buttons, boot circuitry, and antenna keep-out requirements. I will also prepare the requested Gerber and drill outputs, BOM with manufacturer and sourcing references where available, pick-and-place and assembly documentation, pin mapping, and concise DFM notes for the initial assembled boards. Choose me to turn the working prototype concept into a complete fabrication package focused on electrical correctness and manufacturer readiness.
₹1,500 INR in 2 days
2.4
2.4

Hello, I’d be happy to design your production-ready 4-layer ESP32-S3 AI companion PCB and prepare the complete manufacturing package for JLCPCB, PCBWay, or Lion Circuits. I understand the goal is to convert your working ESP32-S3 prototype into a compact custom board while maintaining firmware compatibility. I can handle: - KiCad schematic and 4-layer PCB layout. - ESP32-S3-WROOM-1-N8R8 integration with correct module footprint and antenna keep-out. - Native USB-C programming/charging with correct CC resistors. - I2S MEMS microphone and MAX98357A Class-D amplifier for simultaneous audio operation. - SSD1306 OLED, user buttons, and hidden Boot pad. - Li-ion charging/protection, power switch, and 3.3 V regulator with adequate current capacity. - Correct GPIO assignment, including avoiding GPIO35/36/37 reserved for PSRAM. - Proper grounding, power distribution, signal routing, and DFM considerations. - Component selection prioritizing available LCSC/JLCPCB parts. - ERC/DRC checks and final manufacturing review. Deliverables will include KiCad source files, Gerbers, drill files, Pick-and-Place/CPL, assembly drawing, complete BOM with manufacturer/LCSC part numbers, pin map, and DFM notes. I have experience with embedded hardware, mixed-signal PCB design, multilayer layouts, power distribution, and component selection, and can approach this as a complete production hardware design. Best regards, Moatasem
₹1,050 INR in 7 days
0.6
0.6

Hello, I have hands-on experience with ESP32-S3 development, I2S audio interfaces, OLED displays, power circuits, and custom PCB design using KiCad and EasyEDA. I understand your requirement for a compact 4-layer ESP32-S3 AI companion PCB using the ESP32-S3-WROOM-1-N8R8 module. The design includes native USB-C programming, an I2S microphone, MAX98357A amplifier, SSD1306 OLED, buttons, and a protected rechargeable battery power system. My proposed workflow: 1. Review your existing prototype and hardware specification. 2. Select suitable JLCPCB/LCSC components. 3. Develop the schematic and PCB layout. 4. Review antenna clearance, power distribution, and audio routing. 5. Perform ERC/DRC checks and prepare Gerbers, BOM, CPL, and editable design files. I can share examples of my previous ESP32 projects and PCB designs. Before confirming the final scope, please share your hardware specification, board dimensions, and battery/charging requirements. Best regards, Vector Robotics
₹700 INR in 1 day
0.0
0.0

I understand your project. Please have a look at the example boards I created by visiting the portfolio section of my profile. For the hidden boot pad, we can have an unpopulated exposed pad, is that what you mean?
₹20,000 INR in 7 days
0.0
0.0

A production-ready ESP32-S3 board requires careful power, USB, I2S, PSRAM-pin, and antenna-clearance decisions, and my PCB design, circuit design, embedded systems, and DFM skills directly match this project. I can design around the ESP32-S3-WROOM-1-N8R8 while respecting the reserved GPIO35–37 pins and creating the required 4-layer layout for reliable manufacturing. My electrical engineering background supports the complete hardware package: KiCad schematic, native USB-C with CC resistors, protected lithium-cell charging, suitable 3.3 V regulation, EN and Boot circuitry, I2S microphone and MAX98357A amplifier connections, OLED and button interfaces, and the required antenna keep-out. I can also prepare manufacturer-ready Gerbers, drill, pick-and-place, assembly drawing, BOM with sourcing references, pin mapping, and concise DFM notes for the initial assembled boards. I am ready to turn the working development-board prototype into a clean, testable manufacturing design and would welcome the opportunity to build this PCB package for you.
₹20,000 INR in 3 days
0.0
0.0

**Chandan Sheikder - Freelancer** ### Project Title: Production-Ready ESP32-S3 AI Companion PCB (Gerber PCB Design) #### Introduction I am excited to apply for this opportunity as a highly skilled and experienced freelancer with expertise in Robotics, specifically focusing on SLAM, ROS, Python, C++, and sensor fusion. My background has been built on a solid foundation in these areas, with over 12 papers published in top-tier journals. I am particularly proficient in developing and implementing algorithms for real-time localization and navigation using sensors such as LIDAR, cameras, and ultrasonic sensors. #### Project Description I have an existing ESP32-S3 board with various sensors attached to it. My current goal is to design a PCB that allows seamless integration of AI algorithms for autonomous driving. The project will involve designing a custom PCB to accommodate the various components required for the AI system, as well as ensuring that the PCB is production-ready and adheres to all relevant safety and compliance standards. #### Hourly Rate: $35/hr I am committed to delivering high-quality work within my hourly rate of $35 per hour. I will ensure that my projects are delivered on time and within budget, with a focus on maintaining a positive and professional demeanor throughout the entire process. #### Expertise in Robotics My expertise lies in a wide range of robotics applications, including autonomous driving, localization, mapping, obstacle avoidance, and path planning. My experience has been gained through extensive research and development in these areas, with a focus on developing innovative solutions that address real-world problems. #### Skills - **Robotics**: Expertise in SLAM, ROS, Python, C++, Sensor Fusion - **Algorithm Development**: Experience in designing and implementing algorithms for real-time localization and navigation using sensors such as LIDAR, cameras, and ultrasonic sensors - **PCB Design**: Proficiency in designing custom PCBs to accommodate various components required for the AI system - **Safety Compliance**: Knowledge of relevant safety and compliance standards (e.g., EN 50121, ISO 26262) - **Team Collaboration**: Ability to work effectively with a team of developers and stakeholders #### Availability I am available to start on this project immediately and will work on it for the duration of 3 months. Please let me know if you have any questions or concerns. --- Thank you for considering my application. I look forward to the opportunity to contribute to your esteemed team. Best regards, Chandan Sheikder
₹600 INR in 7 days
0.0
0.0

Tenes un lindo proyecto que interesa llevar a cabo en toda la etapa de desarrollo y producto final. Testing incluido y programación
₹1,050 INR in 7 days
0.0
0.0

Hello, I can design your AI Talking Companion PCB using the ESP32-S3-WROOM-1-N8R8 module. I have experience in embedded systems, ESP32 hardware, digital interfaces, and power supply design. Deliverables: • Complete schematic and 4-layer PCB layout. • Native USB-C programming, I2S MEMS microphone, MAX98357A amplifier, SSD1306 OLED, buttons, and battery charging/protection. • 3.3V regulator rated for 500–600mA minimum. • Gerber, drill, pick-and-place, assembly drawing, and complete BOM with manufacturer/LCSC part numbers where available. • GPIO pin map and DFM notes for five assembled boards. I will ensure proper antenna clearance, avoid PSRAM-reserved GPIO35/36/37, and support separate I2S audio input/output. I will verify footprints, component availability, and manufacturing requirements. Timeline: 10–15 working days. Bid: $500 (design only). Fabrication, assembly, components, and shipping are excluded. I use Altium Designer. Please confirm whether Altium files are acceptable or native KiCad files are mandatory. Best regards, AVS MORLE SOLUTIONS
₹25,047 INR in 18 days
0.0
0.0

Hi, Greetings from OSTronik India! We are a technology-driven company specializing in Power Electronics and Embedded System Design integrated with Artificial Intelligence (AI) and Mobile Application Development, delivering reliable, industrial-grade electronic and software solutions—from concept to mass production, all under one roof. Our in-house capabilities include R&D, Firmware Development, Hardware Design, Mobile Application(Android & iOS), Prototyping, and Scalable Mass Production, with a strong focus on quality, performance, and cost efficiency. Core Expertise: • Microcontrollers: PIC, STM32, ESP Family, AVR. • Microprocessors: Raspberry Pi • Development Tools: MPLAB X IDE, STM32CubeIDE, Arduino IDE, Atmel Studio, VS Code • Hardware Design: Industrial-grade multilayer PCBs using Altium Designer with optimized power design, isolation handling, and EMI/EMC compliance • Communication Protocols: UART, SPI, I²C, CAN, Modbus, MQTT, LAN, S-Bus, RS-485 Mobile Application Capabilities: • Custom Android & iOS mobile applications for device control, monitoring, and data visualization • Real-time dashboards, cloud connectivity, and secure user authentication • Seamless integration between IoT platforms and mobile apps We have successfully transformed multiple concepts into market-ready electronic and mobile-enabled solutions. We would be glad to share a brief reference video. Let’s schedule a meeting to discuss your requirements in detail. Best Regards, Team OSTronik India
₹1,050 INR in 7 days
0.0
0.0

Hello, I can prepare the ESP32-S3 companion PCB package for ₹1,050, targeting 7 days from an agreed kickoff with the board plan and mechanical limits confirmed. Relevant completed Upwork work includes “Custom ESP32 IoT PCBA Design with Relay and RF Module” ($700) and “Pcb sch”. My portfolio includes ESP32-S3 multilayer hardware; these are hardware credentials, not Freelancer ratings. I will use the specified WROOM-1-N8R8 module and a four-layer KiCad layout, preserving the antenna keep-out and avoiding PSRAM-reserved GPIO35–37. I will map native USB-C, EN/GPIO0 boot control, two I2S interfaces, SSD1306 and buttons against your existing firmware. The power review will cover cell charging/protection, USB/battery behavior, regulator headroom and transient current, with the MAX98357A supplied from the battery. Microphone selection and assembly part availability will be checked against LCSC/JLCPCB at BOM release. Deliverables: editable schematic/PCB, pin map, Gerber/drill, pick-and-place, assembly drawing, MPN/BOM with supplier references and DFM notes for five electrical-test boards. I will include ERC/DRC results and a staged power/USB/audio bring-up checklist. Please share the allowed dimensions, cell/charging details and prototype pin map; we will confirm scope and scheduled start before the work begins.
₹1,050 INR in 7 days
0.0
0.0

Jaipur, India
Payment method verified
Member since Jun 18, 2021
₹600-1500 INR
₹400-750 INR / hour
₹600-1500 INR
₹12500-37500 INR
₹600-1500 INR
$30-250 USD
$250-750 USD
$110-250 USD
$3000-5000 USD
₹100-400 INR / hour
₹750-1250 INR / hour
₹1500-12500 INR
£10-20 GBP
£750-1500 GBP
₹1500-12500 INR
₹150-350 INR / hour
$250-750 USD
₹1500-12500 INR
$15-25 USD / hour
$3000-5000 USD
$5000-10000 USD
₹1500-12500 INR
$30-250 USD
$10-30 USD
$250-750 USD