Lukket

Elevator Controller

We are looking for an experienced engineer to design and write sample functional firmware for an elevator controller.

The controller will have can bus, usb and ethernet connectivity. We need to have remote telemetry and control.

The other inputs/outputs will be defined.

We appreciate innovative design and suggestions.

We need:

-The schematics, PCB layout and BOMs.

-The source code and binary code of sample firmware. The source code will be well commented for further development. The sample firmware will be used to prove that all features of the controller work properly and will be the base for further development. Also, sample program is needed for pc to communicate with usb port.

-Working Prototype board with the sample firmware.

Also, we prefer Altium 09.

No milestone payments

Færdigheder: Elektrisk Ingeniørarbejde, Elektronik, Indbygget Software, Microcontroller, PCB Layout

Se mere: elevator pcb, pcb design elevator, elevator controller pcb, microcontroller prototype, looking electronics engineer design, engineer electronics, board prototype, binary code sample, elevator control firmware, elevator pcb board, elevator controller engineer, elevator controller schematics, schematics design, prototype pcb, pcb development, pcb design altium, pcb altium, microcontroller design, firmware development, ethernet, electronics prototype, electronics pcb microcontroller, electronics engineer, controller, control board design

Om arbejdsgiveren:
( 1 bedømmelse ) Athens, Greece

Projekt-ID: #978522

21 freelancere byder i gennemsnit $2405 for dette job

jobykpaul

Please check my PM for details

$2500 USD in 45 dage
(33 bedømmelser)
7.3
MIKY4227

Senior ENGINEER. have at least 30 years experience developing Hardware and Software

$3000 USD in 45 dage
(19 bedømmelser)
5.1
scribblerspk

Lets get started !!!

$3000 USD in 60 dage
(7 bedømmelser)
5.0
reallifetech

See details in MB.

$2555 USD in 40 dage
(15 bedømmelser)
4.3
alit56

I've developed elevator controllers before. Please see PMB.

$2000 USD in 60 dage
(6 bedømmelser)
4.1
ganduyantech

Please see PM

$1900 USD in 45 dage
(7 bedømmelser)
3.9
adipdutt

please see PM

$3000 USD in 45 dage
(4 bedømmelser)
3.2
ecadpcb

I am an Layout PCB Engineer located in Mexico with a very good experience in PCB design, shematics, Bill materials, gerber files. My refereces is products of consum and equipament audio,medical,supply power

$2500 USD in 30 dage
(1 bedømmelse)
2.5
kamranbabar

Hi, Please see the PMB.

$2000 USD in 45 dage
(1 bedømmelse)
2.2
usamacpp

Please check PMB

$3000 USD in 40 dage
(2 bedømmelser)
2.2
satyavolu

I am an embedded software engineer with 12 years experience. I am located in the US.

$2500 USD in 45 dage
(0 bedømmelser)
0.0
AZDigitalS

We are a group of experience electrical, mechanical, software in US and Vietnam. We have all the technologies and skill to complete your your project. We have Altium summber 09.

$1500 USD in 40 dage
(0 bedømmelser)
0.0
HARIKRISHNANG

Hi, I am ready to start the elevator,waiting eagergly for your target floor

$1950 USD in 30 dage
(0 bedømmelser)
0.0
idevasia

We can do for you by using modbus protocol on TCP/IP or RS485 or .....

$3000 USD in 60 dage
(0 bedømmelser)
0.0
nalins

please my PM

$2500 USD in 45 dage
(0 bedømmelser)
0.0
morrispan

1.) Hope I could provide you satisfied service. 2.) I also could provide you manufacturing service.

$2000 USD in 40 dage
(0 bedømmelser)
0.0
volansys

Hi, Please check your PMB for more details. regards, Volansys

$3000 USD in 45 dage
(0 bedømmelser)
3.7
EmbedSol

hi please see PM

$1500 USD in 60 dage
(0 bedømmelser)
0.0
fseratti54

We have 8 years designing hardware using Protel DXP and later Altium. We design for high performance processors (32 bits, +100Mhz). We can do this, we offer professional solutions and commitment.

$3000 USD in 30 dage
(0 bedømmelser)
0.0
progsel

Hi, I designed different HW with similar requirements. There is no problem at all

$2000 USD in 40 dage
(0 bedømmelser)
0.0