I gang

rc servo design

This small project requires very basic wireless control function of a small rc servo. The project requires a single button transmitter with battery power supply to communicate with a base station that controls the RC servo. Range of the transmitter will be 10M. Basically it is a repackaging of an rc car control system on a single servo. This project needs to have consideration for production. Will need a working prototype built as part of this project.

Transmitter:

AAA battery powered control of base station.

Single button on transmitter to control servo. Button needs to be able to control the servo like a throttle.

Wake up transmitter when button pushed 3 times. Sleep timer 2 min after activation

Wireless communications cannot interfere with 457 kHz systems.

Transmitter pairing to base station needs to be simple. Transmitter may need to be replaced so simple paring in critical.

10Meter wireless range.

Base station:

Toggle switch to power up base station from 12V power supply.

Beeping signal to indicate system powered up. 2 sec interval

Receives signal from transmitter to control RC servo Approx 30 Degrees of position used on servo.

10 meter communication with transmitter. When communication fails system should detect loss of transmitter and power off the base station until the system power has been cycled on/off Via toggle switch

Servo fail close to original start position

Base station should have ability to adjust the trim on the servo.

Compact size is desired, will need considerations for vibration and the elements. Ideally product would have temp rating to - 30 Degrees.

Færdigheder: Elektrisk Ingeniørarbejde, Elektronik, PCB Layout

Se mere: throttle up, single system design, product design considerations, power systems design, min range, design controls, basic electronics engineering, basic electrical and electronics engineering, temp position, engineering product design, electronics & communication engineering, prototype car, power meter, electronics prototype, electronics and communication, Electrical System , electrical product, detect car, car throttle, car part prototype, 12v power supply design, wireless signal, design rating system, project vibration, basic engineering design project

Om arbejdsgiveren:
( 1 bedømmelse ) revelstoke, Canada

Projekt-ID: #6020656

Tildelt til:

uzair11235

hi i have worked on servo control using wireless and also have worked with the one button transmitter and receiver you require. contact me to provide me more details regarding the size of the steup

$25 CAD / time
(1 bedømmelse)
1.0

8 freelancere byder i gennemsnit $21/time for dette job

techhelp56935

Hi, I was wondering if you required hardware to be delivered or the design/ circuit diagram only. Best Regards. TH

$22 CAD / time
(4 bedømmelser)
3.5
nadeemrizwan

A proposal has not yet been provided

$23 CAD / time
(4 bedømmelser)
3.4
ElectrSoftDesign

Hello..Im Electricl-electonics Engineer and i have experience about the microcontroller RF systems...If you contact with me i c send you my works..

$20 CAD / time
(4 bedømmelser)
2.5
poliop05

For More Discuss S*ype I*d>>>>>loplat<<<<<< Also Hire me---- [url removed, login to view]

$22 CAD / time
(0 bedømmelser)
0.0
achirasd026

Hi I am an electrical and electronic engineering under graduate, I can easily design your system. Please accept my bid. Thank you.

$15 CAD / time
(0 bedømmelser)
0.0
sudhanshu121

I have read your Project and i have done the same type of job few days ago so i can do your job efficiently

$22 CAD / time
(0 bedømmelser)
0.0
sadiqamin1988

A proposal has not yet been provided

$22 CAD / time
(0 bedømmelser)
0.0
zdhovey2000

UAV and extensive experience in both RF and microprocessor design. Have done projects like this for my own use many times.

$20 CAD / time
(0 bedømmelser)
0.0