I gang

ATMEGA based eletronic board

The goal of the project is to design an electronic board. The sub tasks are the folowing:

- Create a schematics based on references design and a specification reports containing the modifications we would like to do to the reference design (specific connector, additionnal memory).

- Create the layout for a 4 layer PCB.

- Develop a firmware fort validation purpose.

The board will have an ATMEGA MCU communicated over I2C with one device and over SPI with two devices: a simple Dataflash and a Wifi module.

The TCP IP stack for the Wifi module is already developed so no heavy integration is required. Only simple communication over SPI and I2C with simple devices.

Færdigheder: Elektrisk Ingeniørarbejde, Elektronik

Se mere: spi engineering, integration specification, goal engineering, electronic electrical engineering, electronic and electrical engineering, electrical & electronic engineering, electrical and electronics engineering, electrical and electronic engineering, electrical and electronic, engineering schematics, electronics & communication engineering, tcp ip, tcp / ip, schematics design, project board, pcb board, mcu, I2C, fort, electronics and communication, electronic PCB, electronic board, electrical layout, communication engineering, board layout

Om arbejdsgiveren:
( 2 bedømmelser ) Bruges, France

Projekt-ID: #966932

Tildelt til:

AdrianoCampos

Hi, I am Electronics Engineer with 9 years experience in development, prototyping and testing of products. Can I be the hardware supplier in a few days and for low cost. If you have questions please contact-me by a Mere

$900 USD in 15 dage
(1 bedømmelse)
3.9

17 freelancere byder i gennemsnit $1066 for dette job

u04f061

Please check PM

$750 USD in 12 dage
(1 bedømmelse)
2.5
STRpt9

I have experience in PCB design and will do a professional job for you.

$1300 USD in 35 dage
(2 bedømmelser)
1.4
iHEXMachine

Hello. Please see your PM. Regards.

$1320 USD in 45 dage
(0 bedømmelser)
0.0
ElectroLady

I am a researcher in electronics, and I am usually design my project by myself, using Protel DXP or Eagle professional, with 1 layer, 2 or 4, it's ok.

$1500 USD in 7 dage
(0 bedømmelser)
0.0
Nagalakshmik

Iam ready to do this job

$1400 USD in 20 dage
(0 bedømmelser)
0.0
luis191172gomez

Hi I am a Spanish engineer very familiar with the job fair looking for, I made numerous plates with Cadence Allegro for the past 10 years developing HW Telecommunications equipment you can find on this site: [url removed, login to view] Mere

$1200 USD in 60 dage
(0 bedømmelser)
0.0
walden123

Will deliver a professional job.

$1050 USD in 15 dage
(0 bedømmelser)
0.0
mohamedabozied

Dear Sir , i'm a mechatronics engineer and i can do this project for you by eagle software

$750 USD in 10 dage
(0 bedømmelser)
0.0
techss2

pls see pm for details

$750 USD in 15 dage
(0 bedømmelser)
0.0
locson

For your schematic and PCB layout, it should take me less than 1 week. Firmware will be around 1 week, but I have some SW guy from Asia taking care it for me. I can have the design for you ready in 10 days, but I need Mere

$750 USD in 15 dage
(0 bedømmelser)
0.0
ecadpcb

I am an Layout PCB Engineer located in Mexico with a very good experience in PCB design, shematics, Bill materials, gerber files. My refereces is products of consum and equipament audio,medical,supply power

$1400 USD in 35 dage
(0 bedømmelser)
0.0
PCBDOC

Have designed with ATMEGA chips and throughly familar with serial communications. Have also designed embedded projects with WiFi modules.

$1500 USD in 30 dage
(0 bedømmelser)
0.0
vidyadhardeo

please check the PMB.

$750 USD in 30 dage
(0 bedømmelser)
0.0
electrochak

At full time work, such a project takes me 7-12 workings days. But, as it for me an additional earnings, time is greater by about 2 times. Making of prototype of PCB is not included - only project. For additional info Mere

$900 USD in 22 dage
(0 bedømmelser)
0.0
microLED

Please check private message

$850 USD in 15 dage
(0 bedømmelser)
0.0
bachelorlko

Please see the attachment we have designed for AT89C51 ...hope to hear from you soon.

$1350 USD in 30 dage
(0 bedømmelser)
0.0
maliknaeemnisar

I am an Layout PCB Engineer located in Pakistan with a very good experience in PCB design, schematic, Bill of materials, Gerber files.

$750 USD in 25 dage
(0 bedømmelser)
0.0