I gang

RGB LED driver controller

I have a 10w RGB LED package (3w per colour) and need to drive it so we can select:

Just red

Just green

Just blue

White (all three together)

Yellow (red & green together)

Each of the LED's requires different voltages, and current limited to 350mA per channel.

I tried previously to do this, but with little success and just destroyed the LED's.

To limit the current I tried adding NSI50350ADT4G's, but they get VERY hot so dont think this is a usable solution. Also, as they get hot, the current goes down so not a great idea.

The LED's are common anode

Here's a link for the LED

https://www.amazon.co.uk/gp/product/B01DBZK64K/ref=ox_sc_act_title_2?smid=A29VZUSG1WM39I&psc=1

I've uploaded an image of the original Chinese flood light controller, but dont want to use the IR remote. Must be via a single N/O switch.

I want to control the colour by pressing a N/O switch. Each time it's pressed, it changes to the next colour.

Once tested on an arduino, I plan to build it on a ATMEGA328-AU chip.

There are lots of circuit ideas out there about how to manage voltage and current for these LED's, but no guess work please. If you dont have the skill and knowledge, dont bid.

This is a re-posted project as it was given to a freelancer without the appropriate electronics knowledge to complete it properly.

Evner: Arduino, Kredsløbs Design, Elektrisk Ingeniørarbejde, Elektronik, Microcontroller

Se mere: rgb led controller, high power rgb led driver, rgb led driver circuit, rgb led driver ic, rgb led driver i2c, rgb led driver arduino, rgb led driver ic pwm, rgb led driver circuit diagram, rgb led pic controller, rgb led controller schematic, rgb led controller projects schematic, rgb led controller project, rgb led controller 89c2051 asm, rgb led controller, rgb led bluetooth controller

Om arbejdsgiveren:
( 40 bedømmelser ) Offord Darcy, United Kingdom

Projekt ID: #17155631

Tildelt til:

anhvu100

Hello, First of all, selecting NSI50350ADT4G is a wrong decision as it is a linear converter. That means any unused energy is consumed on this IC and produces a lot of heat. When the temperature reach the thermal sh Flere

$250 USD in 7 dage
(23 bedømmelser)
5.3

27 freelancere byder i gennemsnit $162 på dette job

bijan01in

Hi i am interested to your project. I am familiar with electronics, PIC microcontroller as well as pcb design by eagle. Thanks.

$250 USD in 10 dage
(71 bedømmelser)
5.5
sky19130

Hi, dear! I saw your project. I am a interested in your current driver project. I can do it and i wold like to discuss the details. I will best. Thank you.

$177 USD in 3 dage
(32 bedømmelser)
5.3
mohameedtareq

Hello sir don't worry about the stand a,one arduino I'm professional at it ,I make many circuits with builtin arduino platform by atmega328ic Let's move to main part I'll control your rgb leds by tip122 or othe Flere

$133 USD in 3 dage
(12 bedømmelser)
4.4
AhmedSobhiSaleh

Hi, I am a professional electrical engineer. I am an expert in designing and simulating circuits and writing arduino codes I also have the hardware to test and confirm working code. You can see some of my work in my po Flere

$138 USD in 5 dage
(16 bedømmelser)
4.5
MElizabethp

Hello my name is Maria I am an electronic engineer, I would love to design this circuit for you, I have plenty of experience working with electronic and electric designs (squematic and PCB layouts), programming microco Flere

$250 USD in 3 dage
(5 bedømmelser)
4.5
FarzanSaleem

I have 3+ years of experience in Hardware designing, firmware development and complete Product Development. I will provide you complete hardware consultancy and also i will provide schematics and BOM of circuit. If y Flere

$150 USD in 3 dage
(7 bedømmelser)
4.1
sourabh470

Hello Sir, its an easy task for me. I have 4 years experience in PCB designing in EAGLE (single multilayer and flex) As NSI50350ADT4G has very high PD value 11W without a good heat sink it won't work properly. 2 Flere

$150 USD in 6 dage
(9 bedømmelser)
3.7
jawwadHusNain

hi, I go through your requirements, and found that i can do your project. i have experience in communication protocols and controller also. you may go through my portfolio and projects. thank you

$170 USD in 10 dage
(3 bedømmelser)
3.4
Kristsp

Hi, I am interested to work with your project. To be sure that it works as expected, I would need to source the very same leds you have. For project delivery, do you need complete prototype PCB or just a schematic? Sen Flere

$200 USD in 14 dage
(2 bedømmelser)
3.2
soltracker

How r u?Buddy,,,Its me Imad, Have done 200+ projects regarding matlab, arduino, vb.net, html, php, pcb designing and raspberry pie. U will feel brotherhood..............................

$60 USD in 3 dage
(14 bedømmelser)
3.2
ahmedradwan94

I've experience in power electronics and I've made a 250 watt motor driver before for DC motors. I've experience in Arduino programming also so it won't be a problem for me to implement and test afterwards. Contact me Flere

$166 USD in 5 dage
(4 bedømmelser)
3.2
Omaresl

Hello I'm an engineer in electronics and I can help you with your project Actually I have good experience with Opto electronics. The solution that I can gave you is a Power circuit with a microcontroller that Flere

$90 USD in 5 dage
(4 bedømmelser)
2.3
$116 USD in 5 dage
(2 bedømmelser)
1.3
champsoban

hello there, I am electrical engineer with specialization in electronics engineering. I have been working on arduino microcontroller for 2 years now. I can do this project for you but I will take my time to complete it Flere

$111 USD in 7 dage
(1 bedømmelse)
0.8
$200 USD in 10 dage
(2 bedømmelser)
1.4
anmol2701

Hi, Thanks for sharing the project requirements I am an adept arduino programmer and would like to work on this project Welcome to have an interview session for the project understanding Regards NG Services

$333 USD in 7 dage
(1 bedømmelse)
0.8
cheetahpixie

I can definitely write the code for you, but have not had enough experience with specific parts to be able to tell you much about what to pick. Do you have a Mouser local to you?

$155 USD in 3 dage
(0 bedømmelser)
0.0
mcanerbasol

I've been working on power electronics, LED drivers for 2 years. The circuits I built are the ones that conform to the standards (EN-55015, EN-61000). I do not tell you that the system will be in compliance with the st Flere

$333 USD in 15 dage
(0 bedømmelser)
0.0
$155 USD in 3 dage
(0 bedømmelser)
0.0
Johnwassef

I used microcontrollers alot of times and I am electrical engineer and I enjoy my time doing this stuff.

$155 USD in 7 dage
(0 bedømmelser)
0.0