Longlight Firmware

Hardware description

Light source: 1 or 2 ledstrip SK6812 (similar WS2812) with individually adressable leds.

Ledstrip can be RGB, RGBW or WWA (wharm white and amber)

Length 1 m (144 leds) or custom specified

Microprocessor control board: Teensy LC or alternative

Resistive touch strip with two channels, connected to analog inputs of Teensy.

Touch strip has same length as ledstrip.

At each end of the touch-strip is a separate switch (zone of 20mm) with separate voltage output. Pressing it sends >2v signal to Teensy.

Power supply 5 volt 20A

Mechanical: Lens and led protection, profile, strip and support

Firmware description

The Teensy LC can be programmed as an Arduino compatible board, using Teensyduino installer. [login to view URL]

Libraries for driving LEDs use FastLed and FastLed RGBW

The code can be tested during Skype and Teamviewer sessions, step by step development of code is suggested. It is not necessary to build hardware.

Evner: Arduino, C programmering, Elektrisk Ingeniørarbejde, Elektronik, Microcontroller

Se mere: k eye k10 hcr, clay paky sharpy price, clay paky wash, clay paky led, clay paky a leda k20, clay paky b >- eye, clay paky moving head, clay paky b eye, 1-Need a Mockup using as a guide the drawings provided,, using mobile number find the operator, software engineer in wordpress support profile, customer support profile, by using which software design the car, software seven segment led using 89c51, led strip pattern arduino

Om arbejdsgiveren:
( 0 bedømmelser ) Sweden

Projekt ID: #17186829

12 freelancere byder i gennemsnit $204 på dette job


Hi, I have both worked with WS2812 and SK6812 led strips. I used atmega328(Uno's mcu) and Nextion's LCD. It was spesific project for trucks I would like to share its videos over the chat. Yours Truly, Ali SERBETCI

$500 USD in 10 dage
(30 bedømmelser)

Hi, I hope you are doing well. I have experience in LED based embedded project development. I have worked with WS2812B based LED strips. I have understood your requirements and would like to discuss the project f Flere

$250 USD in 5 dage
(68 bedømmelser)

Hello I have got your job posting “Longlight Firmware” and I am very much interested to work in your project. I am a circuit designer and have more than 5 years experience of working with the Analog/Digital Elec Flere

$200 USD in 10 dage
(35 bedømmelser)
$155 USD in 3 dage
(15 bedømmelser)

Hi, I am a professional electrical engineer. I am an expert in designing and simulating systems and writing arduino codes I also have the hardware to test and confirm working code. You can see some of my work in my por Flere

$166 USD in 3 dage
(18 bedømmelser)

Hello, I believe I could answer the project development needs of your project in terms of firmware development. I have worked with WS2812s before and I have developed a product with them. I have used an ATTiny85 microc Flere

$200 USD in 15 dage
(3 bedømmelser)

Hello I can help you with your project. I have more than 4 years of experience programming embedded systems including arduino. I have some background developing code for Lighting systems. (DMX protocol for lighti Flere

$160 USD in 10 dage
(4 bedømmelser)
$155 USD in 3 dage
(0 bedømmelser)
$244 USD in 10 dage
(1 bedømmelse)

As long as Arduino is concerned, I can make it on it easily. I can also work on this alternative microprcessor.

$111 USD in 5 dage
(0 bedømmelser)
$155 USD in 10 dage
(0 bedømmelser)

I am an experienced Arduino programmer and I have worked with Ws2812 addressable led strips before. Thanks for the consideration!

$155 USD in 3 dage
(0 bedømmelser)