I dont know what the plans would require but I want to be able to hand these to my county to pull the permits and hand them off to the contractors to pour the monolithic walls and footers as well as to the contractors to pour the floor. Need to assume that the floor will hold up to 20K lbs of a vehicle such as an empty dump truck. The building will be partially burried (left and rear walls into a hill) that will have at the maximum 9' of dirt. The sides will be 10' tall at the minimum inside and the center 12' Tall at the minimum clearance inside (Believe top should be around 14' clearance from the floow). Please see the image attached for an idea of what it should look like.

The sides will be 15' wide each and the center will be 20' wide for a total of around 50' wide

The entire building will be between 32-35' deep.

The exterior will be covered in board and batten painted or stained.

As seen in the image attached, please find the daylight windows at the top of the middle section and a man door on the side of the building. Also, there should be a 6' x 12' porch covering the man door on the side of the building (right side) near the corner.

Inside should be as open as possible. If there is no need for support beams down to the floor, great! But if you need them, they should NOT be intrusive as I may need to move equipment once inside.

Please call or email for additional questions.

Evner: Bygnings Arkitektur, AutoCAD, 3D Modellering, 3D Rendering, Hjemme Design

Se mere: installed red5 dont know, hindi dont know translation, flash ecommerce dont know start, send email people dont know, dont know paraphrase, add friends myspace dont know, japanese translation dont know, dont know translated german, open winrar password dont know, dont know spanish translation, dont know winrar password, translate dont know german english french, translate website english dont know source langague, winrar dont know pass, cantonese translate dont know, urdu translationi dont know, i want to zrit a report on mtn cameroon services and i dont know how to start

Om arbejdsgiveren:
( 0 bedømmelser ) Winder, United States

Projekt ID: #32224818

38 freelancere byder i gennemsnit $955 timen for dette job

(732 bedømmelser)
(318 bedømmelser)
(714 bedømmelser)
(155 bedømmelser)
(420 bedømmelser)

Hi, Thank you for reading our proposal. We are a team of five 3-D designers with an experience of more than five years while working together. We have satisfied many clients with our 3-D skills and friendly collaborati Flere

$750 USD in 8 dage
(206 bedømmelser)
(84 bedømmelser)
(61 bedømmelser)
(129 bedømmelser)
(41 bedømmelser)

While briefing your task modeling task that you are looking for GarageDrawing. More than 10 years I have been working with 3d modeling, sculpting, texturing, rigging, lightening and shading. This skill allows me to c Flere

$750 USD in 5 dage
(73 bedømmelser)
(103 bedømmelser)
(85 bedømmelser)

Hello! We are a team of architects with great experience in house design, we can help you with your garage project Check our profile, thank you BOKO

$1125 USD in 2 dage
(28 bedømmelser)
(31 bedømmelser)
(76 bedømmelser)

Hello! I have designed many architectural projects for over 5 years for clients. I'm glad to have the opportunity to offer you my excellent service and work. I want to work on architectural project with you. I can work Flere

$750 USD in 3 dage
(27 bedømmelser)

Hello I am an architect with a lot of experience, if you choose me, I will give you architectural plans + 3D model + Render, you can see my profile and review the comments of my satisfied clients, send me a message to Flere

$750 USD in 2 dage
(12 bedømmelser)
(31 bedømmelser)

hello, I have read all detail regarding GarageDrawing .I have more then 4 years Experience in 3d Model and 3d Graphic Design.I have done similar work in past.I would like to show you my 3d work. You will get from Flere

$784 USD på 1 dag
(24 bedømmelser)