Need a firmware developer for ESP32 coding with pressure sensor

Lukket Opslået 1 år siden Betalt ved levering
Lukket Betalt ved levering

I need to develop pressure sensor based coding for ESP32 mcu. Here, I am planning to use US9111 pressure sensor with mcp3421 ADC converter. I want to measure +5PSI to -5PSI pressure value, with auto zero calibration. When there will no pressure on the pressure sensor that must be zero value at the initial condition. It should be strictly maintain. It can be set by auto zero calibration. I want to measure pressure precisely, so you need to do the coding with exact calculation.

Arduino Elektronik Microcontroller Elektrisk Ingeniørarbejde C programmering

Projekt ID: #35890416

Om projektet

12 bud Remote projekt Aktiv 1 år siden

12 freelancere byder i gennemsnit $69 timen for dette job

Engrusman877

Hi There, I am a senior Ph.D. Level Expert and Have more than 5 years of experience in electronics and embedded design. I have working experience with esp32 and can interface sensors as well. Just check my profile and Flere

$20 USD in 7 dage
(99 bedømmelser)
6.3
Adeel2k14

Greetings thanks for posting the project there i am electrical engineer i have expertise in embedded systems, PCB designing and circuit designing. I can work on latest engineering tools to complete your task. In my exp Flere

$20 USD in 5 dage
(49 bedømmelser)
5.8
SMBelectronics

As a skilled product development engineer with experience in designing and coding pressure sensors, I am confident that I can provide you with the solution you need. I have a deep understanding of microcontroller syste Flere

$500 USD in 5 dage
(53 bedømmelser)
5.9
ShoaibMustafa88

Hi, i would like to know which model of US9111 you are using.. as there are sensitive types and not so sensitive.. if you are using a correct model that can actually detect that range then i see no problem. seems simpl Flere

$50 USD in 7 dage
(4 bedømmelser)
2.9
ghayasa727

Hi! I have understood your requirements about your project with every detail of it. I am an Electrical Engineer with more than 9 years of experience in electronics, circuit design, PCB layout, Verilog, FPGA, Embedded s Flere

$20 USD in 7 dage
(1 bedømmelse)
3.1
Maclavin

Looking for a firmware developer? Hello, I am a PhD writer with over 7 years of experience, I assure you of high-quality work, plagiarism free, instructions followed and on-time delivery. I am interested to hear more a Flere

$20 USD in 2 dage
(1 bedømmelse)
0.0
GregorDitt

I already know what to do, this code initializes the I2C bus and the ADC, and sets the ADC configuration to start the conversion. The ADC data is read and converted to a pressure value in PSI. The auto zero calibration Flere

$100 USD på 1 dag
(0 bedømmelser)
0.0
shivpps9543

1)Developed pressure sensor based coding for ESP32 mcu 2)US9111 pressure sensor with mcp3421 ADC converter 3)measured +5PSI to -5PSI pressure value, with auto zero calibration 4)there will no pressure on the pressure s Flere

$20 USD in 7 dage
(0 bedømmelser)
0.0
santiagodimarco

Electronic Engineer with +2 years of experience designing and developing hardware and firmware. Efficient and quick deliver of project. I have worked with various microcontrollers and created PCB's for medical and auto Flere

$30 USD in 7 dage
(0 bedømmelser)
0.0
Vardhan0109

Dear client, I am a Computer and Communications Engineering student with a strong background in firmware development. I am writing to express my keen interest in your project. With my expertise in firmware development Flere

$15 USD in 2 dage
(0 bedømmelser)
0.0
najlacell

Hi, I'm from PT Tekno Sistem Mandiri in Indonesia. I can help you to make the system your need. I've already created the similar system. I experience IoT, Arduino, ESP32, ESP8266, Microcontroller, Electrical Engineer Flere

$20 USD in 3 dage
(2 bedømmelser)
0.2