Lukket

Arduino prototype for temperature control and stepper motor control with database -- 2

Arduino has to receive data through 2 i2c boards ( Temperature,(current,voltage)) and send data to 1 i2c board (pid controller (4-20ma))

Control the heat with pid controller (according to user requirement)

Control 2 stepper motors ( steps, speed,direction,delay)

the Arduino should start the heat by sending the i2c command to pid controller (4-20 ma) OUTPUT ,

the Arduino should check temperature ( 3 pt100 sensors ) through i2c temp board and how many amps its drawing through i2c data received from power board if any no current is sensing it should send buzzer or signal,

after reaching certain temperature of each sensor it should control the heat or balance the heat by reducing the power output and per user preference ( only control power by adjusting the output power (not on/off ) function

stp mtr 1 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES) :stp mtr 2 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES) ( which loop is long it will execute till them)

stp mtr 1 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES) :stp mtr 2 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES)

stp mtr 1 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES) :stp mtr 2 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) (LOOP ______ TIMES)

AGAIN LOOP ALL THREE N TIMES

IF

AFTER TEMP 1 REACHES (____) BALANCE THE LOAD (___% TO ____%) TO MAINTAIN BETWEEN ___TO___) EXAMPLE ( 345-350 DEG c )

AND

AFTER TEMP 2 REACHES (___)BAL TEMP 1 TO (___TO___) EXAMPLE: (295-300) AND MAINTAIN FOR (___) TIME

AND

STOP THE HEAT

AND

stp mtr 1 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) //(STEPS/SEC, DIR(BKW), NO OF STEPS(__) ) :stp mtr 2 ( STEPS/SEC, DIR(FWD), NO OF STEPS(__) / *********** Delay for (___) seconds*********** /(STEPS/SEC, DIR(BKW), NO OF STEPS(__) )

BUZZER

Note: the stepper motor should start with slow speed and reach full speed slowly

some 6 buttons ( each button user will define( heat , steps ) profile for each button)

pause button

reset button

all data should be saved in My sql and Excel in pc with real time format with program name for (all boards connected at same time)

See temperature power in separate window (live temperature of both sensors and amps and time of running and program name) )

Note: will be running 3 -4 Arduino mega boards at a time with same pc

need separate windows for each program for live monitoring and separate saving of data in excel and mysql

Evner: Arduino, Elektronik, Microcontroller, Elektrisk Ingeniørarbejde, LabVIEW

Se mere: simple arduino stepper motor projects, stepper motor control tutorial, arduino stepper motor projects, arduino stepper motor sketch, stepper motor program, stepper motor arduino, arduino stepper motor projects pdf, arduino stepper motor position control, stepper motor control, arduino laser stepper motor control, arduino stepper motor control joystick, arduino stepper motor control sketch, arduino stepper motor control code, build stepper motor control arduino, arduino laser scanner stepper motor, wireless stepper motor control using arduino, arduino ir remote stepper motor, arduino remote control stepper motor, stepper motor speed control arduino, project-17-stepper-motor-direction-control-using-2-buttons-with-the-arduino

Om arbejdsgiveren:
( 7 bedømmelser ) Visakhapatnam, India

Projekt ID: #24135187

12 freelancere byder i gennemsnit ₹9268 på dette job

EShamaev

As discussed before, more information is needed on boards protocols to make this project. Please forward more information.

₹12500 INR in 10 dage
(2 bedømmelser)
3.6
kahan1994

Hi, I am kahan. I am embedded developer and have much experienced in hardware and software side. Waiting for further discussion. Thank you.

₹7000 INR in 7 dage
(8 bedømmelser)
3.4
jyrens

Am a professional Electrical Engineer with good knowledge in the following areas +Arduino +Microcontroller +Electronics +Matlab +Python among other softwares kindly contact so we can work

₹11111 INR in 5 dage
(1 bedømmelse)
2.3
lightbulb019

Hey There, We're Industrial Professionals with having more than 5 years of wide experiences in Robotics with enabled IoT, various Electronic circuitry (Low and High Power Electronic circuits), Communication (BLE, RF M Flere

₹13000 INR in 14 dage
(3 bedømmelser)
2.1
pratheek1

Hi, this is Pratheek from Bangalore, India. We specialize in IoT and Embedded Hardware Projects. We help startups and companies convert their ideas to hardware products which they can readily sell on the market. We do Flere

₹10000 INR in 7 dage
(0 bedømmelser)
0.0
AlexDhayalan01

Hi, I can understand the scope of the project, I have good amount of industrial exposure on Automation systems, I have previously worked with NEMA class stepper motors and quite fluent with I2C protocol. You Flere

₹10000 INR in 20 dage
(0 bedømmelser)
0.0
MadhavPhD

hello, I am a phd scholar at IIT kanpur. I worked on various project where we have used arduino based microcontroller.

₹12345 INR in 15 dage
(0 bedømmelser)
0.0
rjrajbir24

Wow, Seems like an amazing opportunity !!! My Name is Rajbir Singh an experienced Embedded and IoT Engineer. You would be happy to know that I have more than 5 years of experience working with the Arduino/Steppers/Ser Flere

₹7000 INR in 7 dage
(0 bedømmelser)
0.0
czeiss

Hi I am interested in your offer because of the challenge it means in the integration of the different components they indicate. I am dedicated to projects that are in the industrial area which involve from the creatio Flere

₹11000 INR in 15 dage
(0 bedømmelser)
0.0
Tello01

Hello! My name is Tello García. I am a mechatronic engineer. I have carefully read the requirements of your project. I can do it!. It will be a pleasure to provide you with a solution for this, it would be a rewar Flere

₹1700 INR in 4 dage
(0 bedømmelser)
0.0
stcircuits

ST-Circuits is a Reseach & Development organization engaged in design, development & manufacturing of microcontroller based electronic products for industrial automation & control of any kind of processing machine and Flere

₹5555 INR in 10 dage
(0 bedømmelser)
0.0
vidtech

Hello, I am professional person with 30+ years of experience in electronics and 10+ years Experience in mechanical. I am able to do such works perfectly.

₹10000 INR in 13 dage
(0 bedømmelser)
0.0