...MEGA 2560, SIM900 GSM GPRS Shield, DHT11 Temperature & Humidity sensor module (pictures attached). I need someone that will explain to me how to connect this components(I have wires, breadboard...) and write a simple code. When I send a text from my phone, arduino should reply to me what sensor reads(in this case lets say temperature). I dont understand
...constituera le plan financier. Nous identifions des problemes / questions 3) nous organisons un RDV avec le demandeur (réel ou à distance) (+/- 2 heures) dasn lequel nous allons poser nos questions et challenger les hypothèses émises. 4) sur base de cette réunion , nous finalisons le plan financier et les hypothèses retenues 5) nous dé...
...algorithm works well, the need of modification is in controling two servos, especilly in getting back servos' position. The original demo get servos' position by using four wires servo(PWM Vcc GND feedback). But I cannot find this kind of servo in the online shops. Actually, I have some plans. a. writing an algorithm like this blog, [log ind for at se URL]
bonjour, je souhaiterais avoir un logo a partir du brouillon que j'ai fait, (un sac de courses avec la trace du passag...superposée a la flèche bleu sur un fond rond vers pistache avec un l'ambre du sac de cours en vert pistache plus foncé) j’espère que vous m'avais compris , n’hésitez pas de me poser des questions si jamais c...
...task requires you to make it work (LCD and touch). So we can use this LCD with ESP32. I will supply an ESP32 dev board, and the LCD, you will need a breadboard and jumper wires to make the connections, and probably some soldering skills to set it up. This is the lib: [log ind for at se URL] Please see attached files from
...Terminal) 8. Size: Length X Width X Height (To be determined based on final board size) 9. Bottom Middle side ( 6 inch cable with female waterproof plug containing power wires and module wires combined) 10. Label Front side Height (Lightning Start: Remote Battery Assurance) If you pretty much copy what is done in the drawing to CAD then you will have
...files • expect you to deliver to deadlines set • release your payment immediately on supply and inspection of final high res files IMAGE A - circled items retouched out (wires to be removed) - even colour of grey for the floor - red lines removed - whiteboard cleaned IMAGE B - circled items to be retouched out - even colour of grey for the
I have a light switch that needs changing. I tried to do it myself, made sure that I put all the wires where they were before (ground wire to ground screw, charged wires to one side, etc.) but realized that I was in over my head when I heard popping. Help me out please!
...Design an algorithm to provide the routing table 2. Design an algorithm to find maximum strongly connected sub network 3. Design an algorithm to find the smallest number of wires that are vulnerable to network connectivity 4. Implement the algorithms by using C++/java 5. Test your programs on randomly generated test connected graphs of 50, 100, 150
...SG350-28PP). The server room has got the Mikrotik router and Cisco SG500-28 switch. From the server room we have 4 CAT6 wires running to each zone DBs to uplink the core switch from Server room to LAN DBs. The LAN DBs in turn run wires to different devices – like IP Camera (POE), IP Phone (POE) and then connecting to PCs, directly to PCs, a few to unmanaged
...work or school. 5. SIM card port (need to access card slot with a pin like an iphone) 6. Two LED buttons 7. One main camera (connected to PCB by wires) 8. A second camera (connected to PCB by wires) 9. A buzzer speaker 10. Accelometer Part One (40% of the work): Please take note that you are required to design a circuit board to fit all the
The project is regarding transforming BOM (Bill of Material) data of multiple items in ...Material) data of multiple items in one sheet to separate sheets. E.g. - A Fan is made from 3 Nos blades, 1 Nos motor and 10 Nos screws. 1 motor in turn is made from 3 m wires and 2 Nos plates. [Nos and m are Unit of measurement - Number and Metre respectively]
This isnt a hard job but needs someone to create a high quality finish that looks realistic. 1. Remove the 2 wires from left side of boys head 2. Alter the football shirt to be a different coloured shirt. Perhaps single colour like navy blue or something different that you think looks good. It should look natural and realistic. IMPORTANT:
Hello ! I have developed a RPi Win 10 IoT core UWP app that connects to DHT22 sensors through wires in order to poll temperature and umidity. It works quite well. Now I need a wireless sensor option. I have researched and found out that such sensors would possibly be based on Arduino Pro Mini or ATtiny and would include a transceiver such as nRF24L01+
I need a 3D figure made for Poser 9. I am looking for a generic person figure wearing a baseball cap and standing on some kind of a base so it can stand up freely when printed in 3D later. Perhaps something like a trophy base. The figure needs to be rendered in silver metallic and the baseball hat and base in the same color. I have made a simple rendering
... 1 Nos motor and 10 Nos screws. 1 motor in turn is made from 3 m wires and 2 Nos plates. [Nos and m are Unit of measurement - Number and Metre respectively] So our master excel sheet contains data as - Fan | .1 | Blades | 3 | Nos Fan | .1 | Motor | 1 | Nos Fan | ..2 | Wires | 3 | m Fan | ..2 | Plates | 2 | Nos Fan | .1 | Screws | 10 | Nos