Demolition jobs
I need structural engineering advice for replacing an existing 9-metre retaining wall with attached glass pool fence at my Sunshine Beach property. The new wall must be concrete and strong enough to carry the current frameless glass pool-fence panels, which I want to keep exactly as they are. Site notes • Existing 9m long and 800mm high wall is failing; demolition and disposal are already covered. • Finished ground level behind the wall stays unchanged. • I am open to either a smooth rendered block wall or a textured concrete-sleeper system—please detail the pros, cons and cost implications of each so I can decide before construction. What I expect from you Site inspection of existing structure and recommended remedial works with costing estimates
...front of people searching Google for asbestos surveys in Kent and the wider South-East. Here’s what I need from you: • Audit the entire site and show me where the on-page gaps are—titles, H-tags, meta descriptions, image alt text, internal links, URL slugs and any thin or duplicated copy. • Carry out focused keyword research around “asbestos survey”, “management survey”, “refurbishment & demolition survey”, plus location modifiers (Kent, Medway, Sussex, Surrey, Essex, London). I have a few ideas already but will rely on your data to refine the final target list. • Rewrite or fine-tune page copy so every page answers search intent, flows naturally for visitors and is ready for Google’s crawler. •...
I am enlarging several window openings in a wood-framed exterior wall and plan to install a new HVAC unit in the attic directly above. Before any demolition or equipment placement begins, I need formal structural calculations that confirm the modified wall—and the supporting roof and attic framing—will safely carry all new loads. Your analysis should account for: • The change in load paths created by the larger window headers • The additional point and distributed loads introduced by the HVAC unit (equipment weight and vibration) • Any related shear or lateral requirements for a wood exterior wall in my locality Please provide sealed or ready-for-permit calculation sheets, clearly showing assumptions, governing codes, load combinations, and member si...
...instructions directly into CAD. Add only essential labels needed for clarity. Follow the provided drafting conventions for symbology, hatching, and organization. **Demolition and Existing Conditions** Create demolition layers showing removals and items to remain. Use proper dashed or redline symbology consistent with industry standards. **Quality Assurance** Verify scale accuracy, layer organization, text legibility, and plotting settings. Ensure each sheet is consistent, clean, and production‑ready. ---- The annotated PDFs I will provide supply all design intent, including existing site features, proposed modifications, demolition notes, grading adjustments, and material changes. They eliminate guesswork and allow the drafter to focus solely on accurate tran...
...for screen pixel lit Lumen Watt timing and measure, rfunit piping with octet change kpbs change in running data through logLOGtime change, change of calculation of DDR ready code, add change code, screen p-e Dpta run every pixel no light basic electricity black semi and full lit, run GpU mu GPuaAaUu measure and enhance with preset 495000 choices and calculate non choice version without choices demolition costaurustansinsincoscosantE (E energy measure divide energy time to calculate one logarithmic number in GPU with a sliding number tbu terminality brUbtuStaeyREYnold R is all screen with light on for 1 minute and 17 54 57,4.7 seconds on E .4.7.8.9,,000oOoOoo(7478 pikosecond calculation in nanosecond turmoil in staceysecond SCATtAY2 where all items are in linearity all calculation...
I'm looking for an experienced engineer to build a diesel concrete saw, primarily for roadwork and concrete demolition. Key requirements: - High durability and long lifespan - Proven track record in similar projects - Ability to provide detailed past work documentation Ideal Skills & Experience: - Mechanical engineering - Heavy machinery design - Welding and fabrication Please include past work in your application. We are looking build a tool with that can compete with the Husqvarna FS5000 Floor Saw and Diamond Products Core Cut CC4948DCV Floor Saw. There will be a design change in how the saw is moved. The tool will be able to cut up to 24" depth of concrete and needs to be able to cut straight on its own. We would like to cut down on all the Electronics used on ...
I already have the original CAD file of the property and a set of rough sketches that outline my ideas for the upcoming extension-renovation. Now I need the design package turned into clear, build-ready documentation. Scope of work • Update the existing CAD to show the proposed layout for the whole house, then create separate demolition plans so contractors can see exactly what stays and what goes. • Produce new floorplans that tie the addition seamlessly into the existing footprint. • Develop elevations with full architectural detail—window and door schedules, exterior finishes, key dimensions, and any notes required for permit submission. • Add structural sheets that specify steel and wood members where they interact with the new works (beams, li...
...pressure-treated remains my first choice. Likewise, should you have ideas for built-in irrigation, decorative trim, or an elevated layout, please outline them as optional add-ons with separate pricing. I expect an on-site visit before work begins, a concise timeline, and photos of comparable planter projects you’ve completed. Once we agree on a plan, I’ll release milestone payments tied to demolition, framing, and final hand-off. Let me know your availability for a walkthrough and how soon you can get materials ordered....
I have a set of building layout drawings for a forthcoming renovation that covers the living areas, kitchen, bedrooms, bathrooms, and stairwell. Before any demolition begins, I want an experienced set of eyes to walk through the plans and tell me, in plain language, how I can make day-to-day life inside the finished home feel better. My priorities: • Space utilisation – every square metre should earn its keep. • Natural lighting – I want to maximise daylight without costly structural changes. • Room connectivity – movement between zones needs to feel intuitive, especially around the kitchen hub. Please study the current floor plans, elevations, and any sections you need (PDF and DWG files are available). Then provide: 1. A concise written re...
I need a concise, cinematic teaser that captures the essence of an upscale renovation and leaves viewers eager to see more. You’ll receive 4K raw footage showing demolition, progress, and the finished space, along with my logo assets and a suggested music track. Your task is to craft a polished reel that feels refined rather than flashy—think smooth pacing, tasteful motion graphics, and dramatic before-and-after moments that highlight craftsmanship without revealing every detail. Key deliverables • Final edit in 16:9 and 9:16 (H.264 .mp4, 4K and 1080p) • Open project file (Premiere Pro or DaVinci Resolve) with all linked assets retained • Short text slate for brand tagline and a subtle end card with call-to-action Acceptance criteria • Runti...
...requires. Fix existing first, then add the gap. All 17 must function perfectly. Full list at kickoff. Test every touched path: model + member, desktop + mobile, public + private, every department. Ready for serious commercial use on the site that is already online. Anything not written here is in the attached full brief, or will be communicated as work starts. HOW YOU WILL WORK Surgeon, not demolition. The site already works. Inherit our stack. Check the existing feature first — if it is broken, fix it; if it is weak, upgrade it; if it is missing and required, add it. Prove it on StreamLumi, not a prototype. WHO SHOULD BID Hands-on with live adult cam platforms, WebRTC/HLS, performer + member UIs, tokens/privates, Lovense repair, and multi-org/department products. Do n...
...requires. Fix existing first, then add the gap. All 17 must function perfectly. Full list at kickoff. Test every touched path: model + member, desktop + mobile, public + private, every department. Ready for serious commercial use on the site that is already online. Anything not written here is in the attached full brief, or will be communicated as work starts. HOW YOU WILL WORK Surgeon, not demolition. The site already works. Inherit our stack. Check the existing feature first — if it is broken, fix it; if it is weak, upgrade it; if it is missing and required, add it. Prove it on StreamLumi, not a prototype. WHO SHOULD BID Hands-on with live adult cam platforms, WebRTC/HLS, performer + member UIs, tokens/privates, Lovense repair, and multi-org/department products. Do n...
I’m refreshing an existing kitchen and already have accurate, dimensioned plans in hand. What I now need is a professional set of refined 2D drawings plus photorealistic 3D visuals that let me (and my contractor) see every finish, fitting, and lighting choice before demolition begins. You’ll start from my detailed layout PDFs/DWG files, tidy up any drafting inconsistencies, and then build a fully textured 3D scene. Think realistic materials, true-to-life lighting, and convincing reflections—something that helps me decide on cabinetry colours, countertop styles, and appliance placements with total confidence. Deliverables
 • Updated 2D plan and elevation files (DWG + PDF) ready for permit/contractor use • A minimum of three high-resolution, photorealis...
...Remote Snaz Designs is looking for an experienced Revit Draftsperson / Architectural Technician to assist with residential renovations, extensions and house projects in Brisbane and Queensland. We need someone who understands Australian residential construction and documentation, not just how to use Revit. Key responsibilities - Produce residential construction drawings in Revit - Existing, demolition and proposed plans - Site plans, roof plans, elevations and sections - Door and window schedules - Kitchen, bathroom and internal elevations - Construction details and annotations - Update drawings from designer, engineer and certifier markups - Coordinate project documentation - Identify missing information rather than making assumptions Revit management A major part of this ...
...structurally and spatially. There’s also an opportunity to make use of the height created by that roof form, potentially incorporating a home office and a media or cinema-style space within that volume. Overall, we’re trying to create a practical, well-thought-out extension that gives us the space we need as a family, while making the most of the house we’ve already invested in. Scope of Works: Demolition and removal of existing carport Construction of double-storey extension (~6m x 12m footprint) Ground Floor (New Addition): Master bedroom with ensuite Small laundry Level alignment with existing house (raising slab as required) Upper Floor: Two additional bedrooms upstairs. Shared bathroom. Additional living or breakout space Roof + Form Integration: Extend a...
...extensive adversarial development. Claims have been withdrawn, weakened, divided, rebuilt, or left explicitly unresolved. A strong criticism is therefore not an unwelcome verdict on the exercise; it is part of the exercise. I am much more interested in discovering a serious defect before publication than in accumulating favourable reactions. At the same time, I am not looking exclusively for demolition. A good reader should also be able to recognize when an unusual argument survives pressure, when two apparently unrelated problems may share an important structure, or when an unfinished line of inquiry deserves further work even though its present conclusion has not been earned. Perhaps the best description is this: **I am looking for readers who are charitable toward the quest...
Looking for a designer to create a professional, fully editable flyer system for Multi Arms Co., a junk removal, property cleanout, and light demolition company serving NJ, NY, and PA. We want the brand to feel clean, masculine, strong, modern, professional, and high-end. The design should look like an established service company—not a cheap coupon flyer. Avoid cluttered layouts, cartoon graphics, overly bright colors, or generic low-quality contractor designs. Company: Multi Arms Co. Primary Headline: Need It Gone? We Handle It. Secondary Tagline: Built to Handle It. Supporting Copy: Junk removal, property cleanouts, and light demolition without the headache. Brand Colors: Navy — #132337 Midnight — #090F17 Steel — #707984 Concrete — #BFC1C...
...Engineering — Remote / HybridNew Wiring Diagram: Create a clean, updated electrical schematic mapping the new Syntec controller and Yaskawa drives to the machine's existing chassis, pneumatic valves, and 5-axis head.I/O Mapping: Define all input/output allocations for the tool changer, safety interlocks, and spindle controls. Phase 3: Physical Installation & Wiring — On-Site (Albania)Cabinet Demolition: Safely decommission and remove the legacy Siemens controller, old drives, and obsolete Assembly: Mount and wire the new Syntec controller, Yaskawa drives, breakers, and auxiliary components into the electrical cabinet based on the approved Integration: Replace or rewire end-stops, home sensors, and pneumatic control switches. Phase 4: PLC Programming & ...
...suggest drainage and reinforcement methods, and show me photo examples or sketches of modern-sleek, rustic-natural and classic-traditional finishes so I can choose the best match for the house and landscape. I only want grass, Japanese Buxus and existing tree in the front yard. nothing extravagant. Weeds and twigs have already been cleared. I live at Pennant Hills, NSW Key deliverables • Safe demolition and disposal of the existing wall • At least two design/material options with estimates and visuals • Detailed build plan covering footings, drainage, reinforcement and backfill If you have experience in retaining wall engineering, and can share a portfolio of similar projects, I’d love to see it. Let me know your proposed timeline and any questions...
...Opposite side * Rear * Main entrance * Parking/gate * Elevated/site view if useful * Day views * Evening/night views The approved Milestone 1 geometry must remain the basis of the design. Any change to existing physical geometry must be clearly identified as: PROPOSED PHYSICAL MODIFICATION I need to clearly distinguish cosmetic/finish improvements from interventions requiring construction/demolition. MILESTONE 4 – FINAL PACKAGE Provide: * Final high-resolution day/night renders * Exterior color/material palette * Paint references where possible * Stone treatment recommendation * Aluminum/window finish recommendation * Entrance treatment * Boundary wall/gate concept * Landscaping concept * Exterior lighting concept * Basic dimensioned parking/site layout * Realistic p...
...calculations, so dimensional accuracy and clear structural notes are essential. Please supply editable CAD (DWG or equivalent) plus PDF sheets; a simple 3-D massing or render that helps me visualise the new proportions would be a welcome bonus. If you have experience retro-fitting second storeys onto existing slabs, I’d like to see examples in your portfolio and hear how you typically phase demolition, underpinning and new framing so disruptions on site stay minimal....
I’m converting an attached garage in Anaheim into a Junior AD...only. • Scope of work is limited to the garage footprint; no new bathroom plumbing is involved. • Deliverables must include digital CAD files and stamped PDFs suitable for online intake plus two plotted plan sets if the city requires paper copies. Acceptance criteria 1. City of Anaheim issues the building permit without outstanding corrections. 2. Final drawing set includes site plan, demolition notes, floor plan, reflected ceiling, electrical, elevations, sections, construction details, Title 24 documents, and any structural sheets you determine necessary. 3. All files delivered in both PDF and DWG formats. If you have local permitting experience and can move swiftly, let’s get this JA...
I'm looking for a skilled contractor to transform a former medical office into individual hair salon suites. The project requires light demolition and the addition of new rooms. Requirements: - Remove non-load-bearing walls - Remove built-in furniture and fixtures - Add private hair salon suites Ideal Skills & Experience: - Experience in commercial renovations - Knowledge of local building codes - Ability to create functional, attractive layouts
Follow instruction sheet, provided by employer, to make 10 thumbnails for DDS.
We are seeking an experienced Construction Manager or Owner's Representative to oversee the substantial addition and renovation of an existing single-family home in New Jersey. The architectural and engineering phases are being completed separately. We are looking for someone to take over once the construction documents are finalized and manage the project through permitting, procurement, demolition, construction, inspections, and final completion. We intentionally want to keep the scope flexible to allow qualified professionals to explain how they would approach the project and what services they provide after the design phase. Experience with New Jersey residential construction, municipal permitting, subcontractor coordination, scheduling, budgeting, quality control...
...need to design new make-up air, negative pressure pre-sorting room, dedicated exhaust for commercial washers/dryers, and any fire-rated penetrations so the renovation meets NFPA, local building, mechanical, electrical, plumbing, and healthcare regulations (Colorado). Additionally, the room with the washers and dryers must include a floor drain and a utility sink. Deliverables (PDF + CAD): • Demolition and proposed floor plans • Reflected ceiling, lighting, and power plans • Plumbing risers, water, waste, and vent diagrams tied into existing lines • HVAC layout with airflow calculations and duct routing to existing roof exhaust/air-handling units • Electrical to support two 60lb industrial washers and two 60lb industrial gas dryers, 208v 3phase &...
...remains • Existing exterior door remains • Existing plumbing locations remain substantially unchanged Demolition: • Remove existing cabinets • Remove existing countertops • Remove backsplash • Remove decorative ceiling assembly • Remove two non-structural return walls between kitchen and dining room New Construction: • Install white shaker cabinetry • Install quartz countertops • Install 4" quartz backsplash • Install owner-supplied appliances • Install recessed LED lighting • Install new drywall ceiling • Minor plumbing modifications • Minor electrical modifications REQUIRED DRAWING PACKAGE G0.0 Cover Sheet A1.0 Existing Floor Plan A1.1 Existing Conditions Photos A2.0 Demolition Plan ...
Logo design for new demolition business - I am looking for a freelancer to design a logo for my new demolition contracting business - The name of my business is Hawksbury demolition. - My business is in the construction industry. - I dont have specific colors, but i do have a design preferences for the logo. - I am open to suggestions and changes, but I have a rough idea in mind. - Ideal skills and experience for the job include: - Graphic design - Strong knowledge of color theory and typography - Experience in creating logos for businesses - Ability to incorporate my specific design preferences I will require all project files and versions with and without background etc.
...structurally adequate may satisfy/waive this requirement. We would like to request a site visit from a licensed structural engineer to inspect the existing walkout and provide a written structural assessment. Our objective is to determine whether the existing wall is structurally sound and suitable for its intended purpose, thereby avoiding unnecessary demolition and reconstruction if it is not required. We are not requesting any demolition, construction, or repair work—only a professional structural evaluation and written report. The property details are as follows: Address: 20 Norseman Court, Brampton, ON L6S 5T7 Please let us know if you can provide this service and send us a quotation for the site visit and the structural report....
...discreet) • A dedicated storage room that does not feel like an after-thought Overall aesthetic: clean-lined Modern design. For continuity, plan on tile flooring throughout and keep finishes light and airy. You are free to re-imagine every wall, doorway, and circulation path so long as structural integrity and building codes remain intact. Deliverables I need: 1. Scaled floor plan (pre-demolition and proposed) showing wall removals and new partitions. 2. Furniture and storage layout keyed to the plan. 3. At least two perspective renders of the open kitchen/living zone illustrating materials, lighting, and tile choices. 4. A concise note on utilities—where the washing machine, plumbing runs, and any relocated electrical points will sit. Acceptance criteri...
I’m refreshing my kitchen and want the entire concept built around a...Wood, Stone and touches of Metal for hardware or lighting • Colour palette: soft Neutral tones that won’t date quickly You’ll take those cornerstones and translate them into a full design package. I need scaled floor plans, mood and material boards that illustrate how the wood, stone and metal work together, and at least two high-quality 3D renders so I can visualise the result before any demolition starts. All drawings should be accurate enough for a contractor to quote from, and the final files must be delivered in both editable (SketchUp, Revit or similar) and print-ready PDF formats. Once I approve the concept, a concise specification sheet listing finishes, fixtures and paint re...
TITLE: Animator for 3D Comedy YouTube Shorts — Short Test Clip (ongoing work) ABOUT THE SHOW "Rufus: Badge & Belly" is a family-friendly 3D animated comedy for YouTube Shorts (vertical, ~60–70 sec), following the donut-obsessed police force of the small town of Glazebury — the "Donut Demolition Squad" — narrated by a deadpan dachshund named Rufus. Pixar / DreamWorks / Illumination style. Produced by Sno Bird Productions. WHAT WE NEED We're ramping up and need a fast, reliable animator for ongoing batch work. We provide all the character art and scene images — you animate them: lip-sync, movement, timing, and scene assembly into finished vertical shorts. This is animation, not character design. THE TEST (short — 5 to...
...(Pixar / DreamWorks / Illumination style) set in the small town of Glazebury, following a lovable, donut-obsessed police force — the "Donut Demolition Squad" — narrated by a deadpan dachshund named Rufus. It's warm, funny, colorful, and family-friendly. Produced by Sno Bird Productions. WHAT WE NEED: - Bold, punchy, scroll-stopping thumbnails that stay clear and readable at small sizes - A consistent "series look" so our episodes are instantly recognizable - Designs that match our fun, family-friendly, colorful tone WHAT YOU'LL WORK FROM: We provide everything — our 3D character renders (Rufus, the cast) and brand art (our logo and neon "Donut Demolition Squad" badge). You design the thumbnails around these existi...
...Because I’m undecided about which structural elements should remain, I’m counting on your technical guidance. Please analyse the existing plans, flag any load-bearing constraints, and propose solutions where beams or subtle dividers can do the job without breaking the open sight-lines. To help me (and future contractors) visualise the transformation, I’ll need: • Scaled technical drawings: demolition, proposed layout, reflected ceiling, furniture placement, electrical and plumbing adjustments. • 3D renders or photorealistic visuals for each key room and the outdoor zones, clearly labelled “before” and “after”. • A concise specification sheet listing materials, finishes, and any structural reinforcements you recommend....
...structurally and spatially. There’s also an opportunity to make use of the height created by that roof form, potentially incorporating a home office and a media or cinema-style space within that volume. Overall, we’re trying to create a practical, well-thought-out extension that gives us the space we need as a family, while making the most of the house we’ve already invested in. Scope of Works: Demolition and removal of existing carport Construction of double-storey extension (~6m x 12m footprint) Ground Floor (New Addition): Master bedroom with ensuite Small laundry Level alignment with existing house (raising slab as required) Upper Floor: Two additional bedrooms upstairs. Shared bathroom. Additional living or breakout space Roof + Form Integration: Extend a...
I need an existing demolition plan amended in AutoCAD. Requirements: - Modify existing areas due to changes in project scope - Amend plans primarily for material changes Ideal Skills and Experience: - Proficiency in AutoCAD - Experience with demolition plans and construction drawings - Ability to adapt to project scope changes Please provide samples of similar work.
...project. The final identity must be professionally drawn as clean, editable vector artwork in Adobe Illustrator. COMPANY Name: Clear Path Ground Works Tagline: Serving SW Florida Service line: Land Clearing • Tree Services • Site Development Services include land clearing, tree removal, tree trimming and pruning, forestry mulching, brush removal, site preparation, excavation, grading, driveways, demolition, residential estate work, and commercial site development. Our target customers include luxury homeowners, custom-home builders, developers, property managers, commercial contractors, and municipalities throughout Southwest Florida. BRAND OBJECTIVE Create a timeless, high-end identity that communicates precision, professionalism, strength, trust, reliability, an...
...and restrained piping systems Pipe fittings, flanges, couplings, gaskets, bolts, reducers, and transitions Valves and specialty piping components Equipment connections and piping tie-ins Pipe sleeves, wall penetrations, and mechanical seals Pipe supports, shoes, guides, anchors, trunnions, hangers, brackets, and support frames Miscellaneous structural steel required for piping supports Demolition, modifications, and connections to existing piping where shown Testing, flushing, disinfection, and startup assistance where required by the specifications REQUIRED DELIVERABLES The successful freelancer must provide an organized Microsoft Excel estimate containing: Piping quantities summarized by project area Pipe footage separated by size, material, service, and insta...
...(specifically for the 48-pax cafeteria and custom C-shaped juice bar), and HVAC ducting. The HVAC routing is critical and must fit efficiently under the 14.5 ft beams. Acoustic Management: Integrate specific soundproofing provisions and acoustic ceiling panels, particularly to ensure the silent office cabins remain undisturbed by the central atrium and cafeteria noise. (Note: No major structural demolition of the central atrium is permitted). Required Deliverables: Photorealistic 3D renders of the main atrium, mezzanine, and cafeteria. Finalized 2D CAD files with complete MEP (Mechanical, Electrical, Plumbing) layouts. To Apply: Please provide examples of previous high-density commercial office or coworking spaces you have designed, specifically showcasing your MEP routing c...
...detailing—standard tread-to-riser proportions, simplified reinforcement layouts, and practical shuttering notes. I expect: • Plan, section and elevation views showing exact dimensions, landing alignment with the lift, and connection to the remaining old stairs. • Reinforcement schedule and bar bending details that a site crew can follow without re-work. • A brief method note or call-outs highlighting any demolition extents and construction sequence needed to splice the new flight into the existing structure. Use AutoCAD, Revit or any comparable CAD tool so I can issue DWGs and PDFs to the contractor immediately. Accuracy around the lift shaft clearances is critical—please allow for the lift supplier’s pit and guide-rail zones. Once I review...
I’m renovating my kitchen with one clear aim: to modernize the space from top to bottom. I already have the general layout, but I need a professional interior designer who can take that vision further—translating it into a full design package and an immersive 3D walkthrough that lets me “step into” the finished room before any demolition begins. Style I’m leaning toward a Modern look (my answer to the style question), so clean lines, contemporary materials, and smart, unobtrusive detailing are priorities. I have not locked in a specific colour palette yet, so you’ll have room to recommend options once we explore finishes, lighting, and cabinetry. Scope of work You’ll start with concept sketches or mood boards, then move into detailed 3...
...project. The final identity must be professionally drawn as clean, editable vector artwork in Adobe Illustrator. COMPANY Name: Clear Path Ground Works Tagline: Serving SW Florida Service line: Land Clearing • Tree Services • Site Development Services include land clearing, tree removal, tree trimming and pruning, forestry mulching, brush removal, site preparation, excavation, grading, driveways, demolition, residential estate work, and commercial site development. Our target customers include luxury homeowners, custom-home builders, developers, property managers, commercial contractors, and municipalities throughout Southwest Florida. BRAND OBJECTIVE Create a timeless, high-end identity that communicates precision, professionalism, strength, trust, reliability, an...
...drainage, waterproofing, and a hand-held shower on an adjustable rail. Safety upgrades I definitely need are sturdy grab bars positioned beside the toilet and inside the shower, plus non-slip flooring throughout the room (tiles or sheet vinyl are both fine as long as the slip-rating is high). Please allow for gentle floor grading into the new shower pan so no lip is required. You’ll handle demolition, plumbing relocation if the drain needs moving, waterproof membrane installation, tiling or flooring, and finishing carpentry around the doorway once the sill is gone. Include all fixtures and fittings installation, caulking, and final cleanup. Deliverables • Site-ready bathroom with door threshold removed and level transition • Fully waterproofed walk-in shower wi...
...& Safety Commercial Clarifications Inclusions Exclusions Risk Register Programme Pricing Schedule (blank) Payment Schedule Warranty Defects Liability Tender Acceptance Commercial Protection The document will specifically protect Smart Fencing Solutions from: Scope creep Latent ground conditions Boundary disputes Incorrect survey information Unmarked underground services Hidden demolition costs Disposal costs not identified in the tender Existing concrete and footing removal Rock excavation Tree roots Builder delays Design revisions Delayed access Inclement weather Third-party damage Authority delays Material price escalation before acceptance Additional traffic management Out-of-hours work Temporary works not documented Landscaping reinstatement outs...
...5 Logos in total. The general company color is burgundy, but logos do not exclusively need to he burgundy. The companies and their functions are as follows: 1. Davis Company (parent company, used broadly to refer to it and all companies under it) 2. ID3 Trucking (trucking and logistics) 3. Davis and Son Excavating and Specialized Hauling (excavating, grading, land clearing, asphalt/concrete, demolition) 4. Davis and Son Reno(vation and Hauling), (trash company and potential future expansion into towing) - this companys colors are Burgundy and Gold, like the Washington Redskins. 5. D&S Solutions (primarily Equipment hauling for now). - Icon-based design (flexible) - Same logo for print and digital - Versions needed for both uniforms/merch and website/email Ideal Skills &...
...pattern. Scope of work • Check the slab for high/low spots, then apply the appropriate self-leveling compound so the finished surface is flat and ready for tile. • Supply and install a crack-isolation or uncoupling membrane if your inspection shows it will avoid future movement issues. • Set porcelain tiles (straight lay) with thin-set, maintain consistent joints, and grout neatly. No demolition is necessary; there is no old flooring to remove. • Clean up the site and leave the floor ready for baseboards or trim. Acceptance criteria • Finished floor flat to within 1/8″ over 10 ft. • Uniform grout lines, no lippage beyond 1/32″. • All materials properly bonded and fully cured. I’m ready to select a profess...
...off the back deck. 2) Window Finalization: The window and sliding door sizes on the lake elevation are still being finalized; you will need to adjust the framing layout slightly based on final dimensions I provide. Note: right now I am planning on Weathershield VUE System () Required Deliverables (Full Architectural Set): - Site/Demolition Plan Context: Clearly showing where the existing structure is modified. Note - the addition will NOT seamless connect to the existing structure because the Header for the addition is 9' versus 8' - Proposed Floor & Deck Plans: Incorporating the modified window schedules and the 4' cantilevered deck extension. - Reflected Ceiling Plan (RCP): Detailing the timber frame purlins and vaulted ridge
I have the original PDF file for my apartment and now need an architect-designer who...may be moved. Workflow 1. First, deliver a revised architectural plan showing the new wall positions, annotated with clear dimensions and notes on demolished and new partitions. 2. Once I sign off on the plan, proceed to the interior design package: mood boards, material palettes, and 3D visualisations that reflect the agreed layout. Deliverables – Updated floor plan in DWG + PDF – Demolition/new-partition overlay – Two rounds of revisions on the plan – Interior concept boards (kitchen, bathrooms, master suite) – Final 3D renders and basic furniture layout Kindly mention which software you prefer—AutoCAD, Revit, SketchUp, 3ds Max, etc.—so ...
I’m preparing to revamp both bathrooms in my 3-bed, 2-bath apartment and I’d like the entire concept nailed down before any demolition begins. The vision is decidedly minimalist—clean lines, uncluttered surfaces and a calming, neutral palette that makes the rooms feel larger than they are. Key must-have: a sleek walk-in shower that feels open yet keeps water contained. I’m imagining frameless glass, low-profile drain, and fixtures in brushed nickel or matte black, but I’m open to your professional suggestions if there’s a smarter way to stay true to the minimalist aesthetic. What I need from you: • A complete design package for each bathroom: mood boards, layout options and final plan drawings (PDF + source files). • 3D visualisatio...
