Filtrér

Mine seneste søgninger
Filtrer ved:
Budget
til
til
til
Slags
Evner
Sprog
    Job-status
    1,409 create rpm jobs fundet, i prisklassen EUR

    INTRODUCTION : IT IS A TYPE OF WEAVING MACHINE ADD-ON WHICH WEAVES DESIGN ON CLOTH WHICH IS MOUNTED ON SHUTTLE LOOMS OR RAPIER LOOMS. REQUIRMENT: NO. OF HOOKS...: IT IS A TYPE OF WEAVING MACHINE ADD-ON WHICH WEAVES DESIGN ON CLOTH WHICH IS MOUNTED ON SHUTTLE LOOMS OR RAPIER LOOMS. REQUIRMENT: NO. OF HOOKS: 1440 OPERATING SPEED: 200 RPM MODULE TYPE: M5

    €663 (Avg Bid)
    €663 Gns Bud
    9 bud

    US ONLY I need a Full design (Turn key) of a Tiny Permanent Magnet Generator and the Tiny Motor that will be running this generator. The RPM and the voltage and current out put will be disclosed later. I need all of the build documents such as the schematic/drawing, calculations and the BOM files associated with this design. I'm Looking for a Freelancer

    €837 (Avg Bid)
    €837 Gns Bud
    5 bud

    Hi, This should be simple but I'm getting loads of conflicting answers elsewhere. I have a shaft turning at 90rpm with 750 ft lb torque. I want to turn a generator s...the gearing by a ratio of 1:20. I can't work out if I lose torque when multiplying the gears and therefore what torque and more importantly horsepower I will have at the 1800 rpm shaft.

    €19 (Avg Bid)
    €19 Gns Bud
    4 bud

    ...pressure sensors (4 sensors total). 3/ Magnetic pickup sensor (picks up magnetic strips in the road for timing). 4/ Inductive type pickup coiled around sparkplug lead for rpm reading. 5/ G/force sensor, to monitor corner loads. 6/ Cylinder head temp sensor. 7/ Coolant temp sensor. 8/ Throttle position sensor. 9/ Brake pressure sensor. 10/ Video

    €269 (Avg Bid)
    €269 Gns Bud
    9 bud

    i have a three motors by different powers as the following : 1- 11 KW , 480 V , 60 Hz , 3 PH , 3500 rpm 2- 15 KW , 480 V , 60 Hz , 3 PH , 3500 rpm 3- 45 KW , 480 V , 60 Hz , 3 PH , 3500 rpm actually i need an electrical engineer to make a correct selection for MCCB, contactor and overload for each case . he should make calculation paper . provide all

    €28 (Avg Bid)
    €28 Gns Bud
    2 bud

    ...stop the motor. 3. The system should display the (approximate) speed of the motor. It is ok to display the speed in bands (for example using a number of LEDs). The speed in RPM should be calculated but need only be shown in the debugger. The actual speed must be shown, not the set speed, so that when the wheel is braked and the motor slows, the display

    €161 (Avg Bid)
    €161 Gns Bud
    21 bud

    A wordpress websit project in between. Launched a page. Need one more right away. Page i...Page is built using themeforest licensed theme. Second page you hve to do is to be with same theme only. You will need to configure the W3TC plugin fully, including doing any RPM or any other installs required on the PHP side on the VPS server this site is on.

    €19 (Avg Bid)
    €19 Gns Bud
    7 bud
    Analyse CANbus data Udløbet left

    Mission The mission is to analyse the data on the CANbus on a motor...Instrumentation Cluster to ECU to make the ECU start the engine without the cluster. * Ability to replicate ECU CANbus traffic to be displayed on the instrumentation cluster. For example RPM, Coolant temp, Speed, Gear, Neutral, Check Engine Light (CEL), ABS fault light, Fuel level

    €543 (Avg Bid)
    €543 Gns Bud
    8 bud

    ...if i play the sound in continuous loop and very the engine RPM (from 700 - 6000), the sound should feel like that of an actual two wheeler. I want the freelancer to provide the sound as well as the logic to make the sound link with RPM , so that I can provide them with a simple code where rpm can be varied in a continuous manner and the sound (while

    €72 (Avg Bid)
    €72 Gns Bud
    11 bud

    I need a Full design (Turn key) of a Tiny Permanent Magnet Generator and the Tiny Motor that will be running this generator. The RPM and the voltage and current out put will be disclosed later. I need all of the build documents such as the schematic/drawing, calculations and the BOM files associated with this design. I'm Looking for a Freelancer that

    €530 (Avg Bid)
    €530 Gns Bud
    16 bud

    ...-injectors from min5v up to 12v (fully open) and control of injection time (voltage vs time) -termistor/temperature sensor to condition when it should work and when cold not to work -rpm reading from the hall sensors please no heroes!! You need to be able to know perfectly how it works combined with the engine, please no copy pasters!! there are plenty of free

    €70 (Avg Bid)
    €70 Gns Bud
    8 bud

    I need to control from one to four fuel injectors, these will be controlled by a potentiometer (throttle regulation) problem is inject...-injectors from min5v up to 12v (fully open) and control of injection time (voltage vs time) -termistor/temperature sensor to condition when it should work and when cold not to work -rpm reading from the hall sensors

    €114 (Avg Bid)
    €114 Gns Bud
    10 bud
    Programmer for RPI Udløbet left

    We need somebody to program a RPI Software to get signal from various sensors like heat, vibration, RPM Show these on a trenddiagram and record for aspecific time. Evtl a UI or databank to export it to an excel file.

    €223 (Avg Bid)
    €223 Gns Bud
    5 bud

    Arduino based RPM, torque from a load cell, temperature reader with calculation of power output. Has to measure up to 90,000 RPM, should be auto-calibrating and have a keyboard input plus display. Data logging to be added as future requirement. High precision requested on both RPM and Temperature readings. Has to be used in electromagnetic noisy environments

    €192 (Avg Bid)
    €192 Gns Bud
    9 bud

    I need someone to design a controller of a brushless motor for me. It's a AC brushless / slotless motor. Power rating in the 60W, 200mA, 24V ranges, up to 40,000 rpm. The functionality of the controller includes speed control, gear switch, memory of the current status of the motor, combination of the different keys, LED display, etc.,

    €2949 (Avg Bid)
    €2949 Gns Bud
    22 bud

    chipKIT Max32 Digilent Microcontroller Programming with the following/not limited sensors 1. Accelerometer 2. Temperature 3. RPM [log ind for at se URL] shield [log ind for at se URL] shield [log ind for at se URL] Shield 7. etc

    €235 (Avg Bid)
    €235 Gns Bud
    5 bud

    ...load of an electric motor. Basically a torque and rpm graph over time. System is defined by student for small robotics applications. We can lend an existing system to the student to collect data on. Important numbers are size, weight, min ratio, max ratio, loss vs ratio vs rpm, max torque, max rpm, max power. Market research and conceptualization

    €316 (Avg Bid)
    €316 Gns Bud
    12 bud

    I have a 7inch Nextion display have a look screen in the Attachments. The project needs Motor RPM control and Temperature control with the relay. Only Nextion and experience guys required.

    €173 (Avg Bid)
    €173 Gns Bud
    19 bud

    I have a simple c++ linux project. I'm looking for a developer who can make rpm package for CentOS and deb package for Debian for me.

    €28 (Avg Bid)
    €28 Gns Bud
    7 bud

    Compile wpe webkit for hikey 960 and build rpm to deploy on centos image.

    €27 (Avg Bid)
    €27 Gns Bud
    1 bud
    Trophy icon Redesign a subject page Udløbet left

    ...example (The top image on the left) It has the following Moremac (developer Information) The Point (estate name) Email address Website address Opening Hours Address RPM (Agent name) Under this there will be real estate listings, they can be done in either grids or rows being 2 or 3 across, the attached file shows roughly what we are thinking

    €44 (Avg Bid)
    Garanteret
    €44
    21 indlæg

    Hello Everyone, Looking for C programmer to help add GSSAPI authentication for davfs2 utility. Requirement: 1. Review architecture 3. Run no privileged user....4 / 16-Apr-2016 Written in: C Developer(s): davfs2 team License: GPL NOTE: Selected freelancer will require work with github an commit all patches. We will generate RPM and test.

    €196 (Avg Bid)
    €196 Gns Bud
    1 bud

    Hello Everyone, Looking for C programmer to help add GSSAPI authentication for davfs2 utility. Requirement: 1. Review architecture 3. Run no privileged user....4 / 16-Apr-2016 Written in: C Developer(s): davfs2 team License: GPL NOTE: Selected freelancer will require work with github an commit all patches. We will generate RPM and test.

    €215 (Avg Bid)
    €215 Gns Bud
    7 bud

    ...also ok. This is important and maybe problematic but i can't change tgis parameters because the coefficients of pressure and rotation have high values: Pressure 20 MPa n=15000 rpm per s Material have normal, typical parameters. I can send if you decide (need to be transformed for abaqus): for e.g. Mass density, Thermal conductivity, Melting point, Poisson's

    €27 (Avg Bid)
    €27 Gns Bud
    2 bud

    I want to control with very high accuracy a 3 phase AC motor -hysteresis type- that will be used to power a vinyl turntable...able to provide 33.33, 45.00, 78.00 RPM. I need a bi-directional servo scheme and provision for a screen. Motor voltage about 100-120 Volts and about 50-70 Watts.

    €1135 (Avg Bid)
    €1135 Gns Bud
    19 bud

    Hi Jorge! I'd like to start working with you on an Arduino project; I need to be able to read up to 7 fan RPM sensors, and send a few PWM signals to control those fans at the same time. I'm not sure which Arduino to get that can handle the necessary number of interrupts and want to keep it cost-effective if I were to scale this project (i.e. I know

    €25 / hr (Avg Bid)
    €25 / hr Gns Bud
    1 bud
    Chip programming Udløbet left

    I need you to develop a pr...a program for PCB components NRF52832 and BMX055. The requirements are to extract the below sensor readings from the BMX via Bluetooth: - speed - direction - spin axis and rpm The data has to be refined and filtered before reception on simple interface on PC. I would like this to be developed for Windows using C or C++.

    €154 (Avg Bid)
    €154 Gns Bud
    6 bud
    Trophy icon Rebuild/Redesign this logo! GG Tuning Udløbet left

    ...logo for a tuning garage and i would love for someone to remake it and make it cooler, add some textures or designs/colors. Ideas is two turbocharges with the inside of an RPM Gauge (Speedometer) Both against each other and human engineer brain or icon in the middle. You can play around with the idea but i need a cool logo with turbos for my tuning

    €88 (Avg Bid)
    Garanteret
    €88
    60 indlæg

    I need an accurate code for arduino with no tons of adjusting and experiments. i need a good fast refresh to be able to accurate rpm up to 18.000 (4 stroke engine, motorcycle engine, via hall sensor from engine taken from the camshaft) simple as this.

    €18 (Avg Bid)
    €18 Gns Bud
    3 bud
    CANbus analyse Udløbet left

    ...Instrumentation Cluster to ECU to make the ECU start the engine without the cluster. * Ability to replicate ECU CANbus traffic to be displayed on the instrumentation cluster. For example RPM, Coolant temp, Speed, Gear, Neutral, Check Engine Light (CEL), ABS fault light, Fuel level I will provide logfiles from the motorbike CANbus for you to analyse. I will also

    €100 (Avg Bid)
    €100 Gns Bud
    3 bud
    Control motor rpm Udløbet left

    Need to control motor rpm of motor with Hall effect encoder

    €31 (Avg Bid)
    €31 Gns Bud
    14 bud
    18" slab machine Udløbet left

    Need a machine design and cad output of a 18" slab saw for cutting chalcedony/agate. Main specs are motor 1.5hp, blade rpm 900, arbor diameter 1", 2 sealed ball bearings supporting the arbor, An auto feed table running over two rods with ball bearings, a worm rod to move the table and a second motor to drive the worm rod (the speed will be adjustable

    €378 (Avg Bid)
    €378 Gns Bud
    33 bud

    ...5-5) m, width (1.7-2) m, height (1.3-1.7) m. 9) Top speed is 70 Km/h. Secondary objectives: 1) Walkie-talkie system. 2) Side mirrors. 3) LED headlamps. 4) GPS system. 5) RPM gauge. The project must be designed using Solidwork. Must include chassis design and suspension system. Taking into consideration all forces applied to the car such as the weight

    €300 (Avg Bid)
    €300 Gns Bud
    15 bud

    ...give very buggy readouts for RPM / MPH calculations. My goal is to use a sensor (image attached) that outputs 0 or 5vdc depending on if the sensor is broken or not. This will be mounted on a wheel, and there will be as many tabs (breaking the beam of the sensor) as possible to get the highest resolution possible of RPM readings. The wheel will be

    €123 (Avg Bid)
    €123 Gns Bud
    43 bud
    electric drill Udløbet left

    electric drill with slow rpm and high torch. sender to stop and revers back.

    €167 (Avg Bid)
    €167 Gns Bud
    7 bud

    ...fit on/around motor. Motor housing to fit in to specific shape (provided as cad file) with volute chamber designed around it. I have a known motor with a known loading and RPM and would like to maximise the flow rate and control dispersal. I need a volute chamber designed to match an unusual shape intake and output so there is some challenge involved

    €137 (Avg Bid)
    €137 Gns Bud
    3 bud

    ...Controller. Please find attached Diagram for better idea.... THE MAIN CONCEPT OF APPLICATION: 1- Engine's RPM will be detected by a Non-Contact RPM detector. This RPM information will be given to the Controller. 2- Controller will run the Motor on same RPM as received/detected from of Engine. Reference Line: [log ind for at se URL] 3-

    €195 (Avg Bid)
    €195 Gns Bud
    14 bud
    Trophy icon Create a new Logo for our Brand! Udløbet left

    ...com%2Fimage-vector%2Fkey-logo-symbol-icongraphicvector-260nw-225212653.jpg&imgrefurl=https%3A%2F%[log ind for at se URL]%2Fsearch%2Fkey%2Blogo&docid=IqnS4gSJXOKpIM&tbnid=4ahhDx3kN3-rPM%3A&vet=10ahUKEwityanbhdLdAhUCWBoKHXFaAbQQMwj5ASgBMAE..i&w=347&h=280&bih=917&biw=1680&q=key%20logo&ved=0ahUKEwityanbhdLdAhUCWBoKHXFaAbQQMwj5ASgBMAE&iact=mrc&u...

    €20 (Avg Bid)
    Garanteret
    €20
    85 indlæg

    hi i need a clear code to count rpm from engine (from the spark plug cable or fuel inyector) its going to be part of a longer code so no "delay" functions. also shematics of circuit if needed. engines go up yo 16,500 rpm to be used with nano

    €31 (Avg Bid)
    €31 Gns Bud
    3 bud

    ...stator diameter / plate width, plate material, number of poles, wire gauge, turns, number of parallel wires, voltage. current, torque and efficiency estimates at a few power/RPM values. I would also like a wiring schematic so that I can build a prototype. References: The car this motor will be used in: [log ind for at se URL]

    €1869 (Avg Bid)
    €1869 Gns Bud
    13 bud

    ...) km / hr. the device must recorded 3 error every 5 second . 3- Over 130 km/hr. the device must record 4 errors every 5 second 4- Over riving record an error the RPM needle reach 4500 RPM and stay for more than 2 seconds while the car speed are zero . 5- Harsh breaking as the built in equation from the system to record an error . ( the calibration

    €440 (Avg Bid)
    €440 Gns Bud
    13 bud

    My idea: each explosion in valve cause one vibration. I need a sensor which transfer this vibration to frequency output. Power source Ucc: 12~24V Output: rectangle, 0 to Ucc, freq modulation. I am looking for existing sensor waterproof, dustproof, fit to engine by screw. OR design electronic circuit for this device.

    €110 (Avg Bid)
    €110 Gns Bud
    3 bud
    Trophy icon Whiskey tasting board CNC model Udløbet left

    ...tasting boards for my families whiskey bar in the Scottish Highlands. I will be using hard wood such as oak for milling please include suitable feedrate also and recommended RPM for mill The design is totally up to you! Here are some ideas though [log ind for at se URL] https://www

    €98 (Avg Bid)
    Garanteret
    €98
    17 indlæg

    ...GB 240-pin Kingston DRAM, and one 7200 rpm hard drive? b. [10] <1.5> How much power will the 7200 rpm disk drive consume if it is idle roughly 60% of the time? c . [20] <1.5> Given that the time to read data off a 7200 rpm disk drive will be roughly 75% of a 5400 rpm disk, at what idle time of the 7200 rpm disk will the power consumption be e...

    €16 (Avg Bid)
    €16 Gns Bud
    6 bud

    Design and create Android Application with features of: a) Gather real time vehicle engine information such as intake temperature, engine coolant temperature, MPH, RPM, voltage, etc. b) Car Status Dashboard; which displays the data gathered from the vehicle c) Scan Vehicle; Gather and display detailed information of the trouble code found d) Clear Check

    €130 (Avg Bid)
    €130 Gns Bud
    2 bud

    ...the game to play. b. Choose standard play. c. Choose rotational play where the numbers rotate around the board at one rpm to simulate a rotating board. (Note: the score is whatever the number is when the dart strikes, and one rpm means the numbers change every three seconds.)...

    €3451 (Avg Bid)
    €3451 Gns Bud
    10 bud

    ...Allison Model 250 or Turbomeca Turmo [log ind for at se URL] first thing I have to do is setting the parameters that define the engine: 1.1 power output at the free turbine 1.2. the airflow 1.3. RPM of the free turbine [log ind for at se URL] (temperature in the combustion chamber) 1.5. πc ( pressure ratio) [log ind for at se URL] setting the parameters that define the engine, I ne...

    €149 (Avg Bid)
    €149 Gns Bud
    18 bud
    Digital stir plate Udløbet left

    ...WQ/s1600/[log ind for at se URL] * Digital rpm control 0 -> 3,000 rpm with 100rpm increments * Buttons: on/off, speed up, speed down * Ability to press up or down button and increment speed by 100rpm * Ability to hold down up or down button to quickly increment speed steps * Segmented LCD display or I2C OLED display to show rpm, preference on OLED...

    €214 (Avg Bid)
    €214 Gns Bud
    3 bud

    Preciso calcular força tamanho da roldana..caixa redutora e desenhar e testar ( solidworks) um sistema de contrapeso 2 ton que move um eixo a 1800 RPM

    €88 (Avg Bid)
    €88 Gns Bud
    1 bud
    Rotor Test Udløbet left

    Test the rotor for thrust at 5000 rpm, suggest optimization changes. Its a simple job for expert engineers. No time wasters please . It a seed project and lot more given to successful bidders. My final offer price is 20$ and deadline is 24 hrs. Expert can do within couple of [log ind for at se URL] File is attached here.

    €17 (Avg Bid)
    €17 Gns Bud
    8 bud