Filtrér

Mine seneste søgninger
Filtrer ved:
Budget
til
til
til
Evner
Sprog
    Job-status
    10,651 PCB altium jobs fundet, i prisklassen EUR
    pcb desing Udløbet left

    pcb desinger

    €138 (Avg Bid)
    €138 Gns Bud
    26 bud
    pcb desigg Udløbet left

    timer concept lcd 3 relay 3 buttons rtc 6 adc (op amp circuit)

    €90 (Avg Bid)
    €90 Gns Bud
    19 bud
    Tray_V2_Cover Udløbet left

    PCB cover for Tray V2

    €32 (Avg Bid)
    €32 Gns Bud
    1 bud
    Game switch Controller 6 dage left
    VERIFICERET

    1) create Software for PCB to communicate with network devices. 2) create firmware and Webpage setting for RN-1723 to act as a network controller. 3) The controller to interface to: Game Switch Buzzer Button Local light on button Outside light to control external light 4) Using MicroChip wifi module RN-1723-EK as a controller https://www

    €47 (Avg Bid)
    €47 Gns Bud
    1 bud
    PCBA Development -- 2 6 dage left
    VERIFICERET

    Candidates has to be from MUMBAI, INDIA. We will block anyone messaging us from other locations. We are developing a project and needs PCB assembly to be done for 2 projects.

    €18 - €36 / hr
    Lokal
    €18 - €36 / hr
    0 bud

    lay out to satellite board in Altuim designer programm .....PCB 6 layer one layer to power , 1 to signal, 1 to ground ,3 to routing

    €905 (Avg Bid)
    €905 Gns Bud
    15 bud

    i want to make a three phase inverter , after that i want to put live data of input voltage , output voltage , battery voltage , load percentage on 4 x...phase inverter , after that i want to put live data of input voltage , output voltage , battery voltage , load percentage on 4 x 16 display , i need code hex file on microc and pcb design of the same

    €14 (Avg Bid)
    €14 Gns Bud
    3 bud

    ...Cable (Required for stop motion and time-lapse) - Bluetooth low-energy communication to Mobile device The job: - I need detailed electrical diagram - List of components - PCB design I listen to recommendations and opinions My project is similar to SLIDERONE of edelkrone ************************************************** CASTELLANO - SPANISH **

    €26 (Avg Bid)
    €26 Gns Bud
    2 bud

    Home automation pcb board

    €22 (Avg Bid)
    €22 Gns Bud
    4 bud

    design my pcb board from scratch

    €169 (Avg Bid)
    €169 Gns Bud
    37 bud
    PCB Design 4 dage left

    I have a Very simple circuit, it's actually a 4 Ohm Coil, with a Kapton Film substrate and a Plastic PCB Frame. It's about 7" x 6", and in reality Its a Diaphragm for a Vintage Loudspeaker Midrange Driver, no longer in Production. The Substrate is Kapton Film, and the Etch is Aluminum. I need these produced to make repairs. I have all the specs, I

    €147 (Avg Bid)
    €147 Gns Bud
    29 bud

    ...some frames by serial port or canbus and you must write the text in a matrix or in LEDs. To control the LEDs, the PCB has an SPI driver so that only by sending via SPI the information will turn on the LEDs. I will be assembling here the pcb in parts. You will send me small examples to test hardware (canbus, serial port, leds driver). Then you will write

    €234 (Avg Bid)
    €234 Gns Bud
    11 bud

    Hello. We are interesting in development of Power Supply, based on Planar transformer multi-layer technology with the main techn...Short circuit protection within Input and Output voltages Overload protection - 200w, Overheat protection Working frequency 300-500Khz PCB Dimensions 152x46mm. Maximum height of Power Supply 15mm (not including PCB height)

    €961 (Avg Bid)
    €961 Gns Bud
    20 bud

    I need to design 1 board which consists of 6 components and 4 pads. I will supply the document for the component dimensions. 1 layer

    €21 (Avg Bid)
    €21 Gns Bud
    15 bud

    I have a PIC32 Visual C++ project that when compiled and the hex is loaded onto my PIC32mz (on a custom PCB). I can use another Windows shell application to send single characters to the PIC, via USB, to execute some functions. The code is in the DevABK C [log ind for at se URL] file. This code basically uses the PIC to reconfigure another chip via SPI. The main

    €344 (Avg Bid)
    €344 Gns Bud
    10 bud
    Design simple PCB 4 dage left
    VERIFICERET

    You need to create .greber file ready for manufacturing PCB. In attachment you can see pdf file on how it is looks like. Some technical details: 1. Two layers (both sides are same - coil). Coil has 50 turns. 2. In the center of the coil there is the 6.5 mm hole and that is where coil from one side connects to the coil from another side. 3. Line

    €30 (Avg Bid)
    €30 Gns Bud
    38 bud
    hardware trainer 3 dage left

    knowlwdge sharing for- hardware system knowledge, Analog Digital circuits,PCB Electrical Power Supply Opamp FMEA , Reliability

    €32 (Avg Bid)
    €32 Gns Bud
    7 bud

    ...False batt_temp: 21 charge_current: 0.0 Project Deliverables: - Soft copy of Circuit Board Design - 10 physical sample Circuit Boards that we can test (You can choose any pcb printer/manufacture that you wish) - Python source code that will go along with it NOTE: Existing circuit board designs that meets the project requirements are acceptable and

    €233 (Avg Bid)
    €233 Gns Bud
    12 bud