3D modeling, not very detailed designing - 23/11/2020 11:44 EST

  • Status: Closed
  • Præmier: $101
  • Modtagne indlæg: 10
  • Vinder: hasankuet

Offentlig Præciserings Opslagstavle

  • Ammar121212
    Konkurrenceafholder
    • 3 måneder siden

    Thanks everyone.. This contest has ended.

    Hope to see you aging in another opportunity >>>

    • 3 måneder siden
    1. hasankuet
      hasankuet
      • 3 måneder siden

      Thank you

      • 3 måneder siden
  • rafihathbd
    rafihathbd
    • 3 måneder siden

    Check #13 will be waiting for feed back

    • 3 måneder siden
  • archshabbir
    archshabbir
    • 3 måneder siden

    #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize

    • 3 måneder siden
  • Ammar121212
    Konkurrenceafholder
    • 3 måneder siden

    Don't hesitate to contact me on DM.

    • 3 måneder siden
    1. hasankuet
      hasankuet
      • 3 måneder siden

      ok working on don't close early

      • 3 måneder siden
    2. Ammar121212
      Konkurrenceafholder
      • 3 måneder siden

      I'm already interested with your work.. Thanks Husain

      • 3 måneder siden
  • rafihathbd
    rafihathbd
    • 3 måneder siden

    Check entry #1 and inbox me if this is what you want. I have the obj file ready

    • 3 måneder siden
    1. Ammar121212
      Konkurrenceafholder
      • 3 måneder siden

      I have commented on your entry..
      Thanks for your great work.

      There's also another 4 models, good luck brother. all the best.

      • 3 måneder siden
  • Rudolph07
    Rudolph07
    • 3 måneder siden

    hello, do you want to print this in parts or all in one solid?

    • 3 måneder siden
    1. Ammar121212
      Konkurrenceafholder
      • 3 måneder siden

      Every piece of the 5 models should be printed individually Rodolfo.. Thanks for the feedback.

      • 3 måneder siden
  • guarco63
    guarco63
    • 3 måneder siden

    Hello, are you sure they use the appropriate 1000: 1 scale?
    Will the water tower be 4mm x 4mm x 13mm high in print?
    At that scale it is impossible to print the columns that apparently measure about 40 cm, which would be 0.4 mm in printing.

    • 3 måneder siden
    1. Ammar121212
      Konkurrenceafholder
      • 3 måneder siden

      No, all measurements in Cm..

      Thanks for your comment & for clearing that up.

      • 3 måneder siden
  • arqfernandezr
    arqfernandezr
    • 3 måneder siden

    #increaseprize

    • 3 måneder siden
  • AyerNielsen
    AyerNielsen
    • 3 måneder siden

    This contest does not make sense and those plans are terrible to work off of.

    • 3 måneder siden
    1. Ammar121212
      Konkurrenceafholder
      • 3 måneder siden

      Dear, it's as mentioned that the work accepted can be tolerated to less than the usual accuracy elsewhere

      It's over 200 years buildings, it's the only data can be provided for such project, I personally have done punch of them and I still work on them just from plans.

      Our work only care for representing the sites as accurate as possible, don't bother to go to the extreme

      It will be printed in 1:1000 scale if you can imagine

      • 3 måneder siden

Bedste indlæg fra denne konkurrence

Se flere indlæg

Sådan kommer du i gang med konkurrencer

  • Opret din konkurrence

    Opret din konkurrence Hurtigt og nemt

  • Få tonsvis af indlæg

    Få tonsvis af indlæg Fra hele verden

  • Tildel det bedste indlæg

    Tildel det bedste indlæg Download filerne - Nemt!

Opret en Konkurrence Nu eller slut dig til os i dag!